Search results

  1. sxer

    Holley Sniper EFI for BBD Carbs

    How about when you pull on the pressure side of the pump?
  2. sxer

    Holley Sniper EFI for BBD Carbs

    A Marine system would be pretty easy. All electronics are on the engine. All you have to provide is switched power and start signal to the solenoid. And a fuel supply. Senders for for oil pressure and water temp are part of the harness between dash and engine.
  3. sxer

    Holley Sniper EFI for BBD Carbs

    Is the vacuum high like a restriction? Maybe you could find a used Marine low pressure electric pump.
  4. sxer

    Holley Sniper EFI for BBD Carbs

    Unless it has changed recently Marine stern drive engines have not had an in tank pump or return line. They have two pumps, a low pressure to pull fuel from the tank and a high pressure in the vapor separator to feed the injectors. Excess fuel is returned to the line from the tank at the engine.
  5. sxer

    Steering stops

    Finally got back to it. I had the stops out too far. The knuckle was hitting the stop before the pump was at the end of it's stroke so it was trying to turn some more and flexing something in the tub. It's all good now.
  6. sxer

    Steering stops

    All rod ends and ball joints are new. I haven’t had the opportunity to look for the problem with someone else turning the wheel. I think it will be apparent when I can do that. The Jeep drives well. Wanders some but have never had it aligned. Did alignment with tape measure. I’ve had it close to...
  7. sxer

    Steering stops

    I have an 81 Scrambler with stock suspension, no lift. 31" tires. At full turn either direction I get a clunk which sounds and feels like the tub oil canning. I am quite sure I can correct this by adjusting the steering stops to eliminate that last bit of turning. I'm just wondering if anyone...
  8. sxer

    AMC401 or LS

    I had the exact same problem as you. I had rebuilt my 258 and it sat on the stand for more than a year while I waited to finish the rest of the Jeep. When I had it all finished and started to drive it, it used oil at the rate of about 600 miles per quart. I didn't see any smoke either. I too...
  9. sxer

    1981 2.5L 151 stalls hesitates and sputters on acceleration

    Sounds like the idle mixture is too lean.
  10. sxer

    4.2 Rattling top end problem

    In 81 there were two different length push rods. When I rebuilt my 81 4.2 I ordered new push rods. When I started it the first time, it ran ok but had a miss at idle. After scratching my head for awhile and checking all the obvious things, I did a compression test. A couple cylinders had no...
  11. sxer

    Step

    I made a step for my '81 Scrambler. I didn't want to drill into or clamp onto the frame so I used an existing skid plate bolt and a body mount bolt. It is very solid. I had it powder coated and added non skid.
  12. sxer

    Push rod lenght

    I am finishing up my rebuild. I fired the engine for the first time last week. It is a 258 that I totally rebuilt. The engine started fine and I set the timing but it had a bad miss at idle. I checked all the obvious things but found nothing wrong. I finally noticed a puddle of antifreeze on top...
  13. sxer

    Air cleaner with Vanco power brakes

    I finally got my Vanco power brake system and installed the master cylinder today. I have an '81 Scrambler with 258 and Carter carb. What air cleaner are you guys using with this set up? It looks like I have a maximum of 3 1/2" from the center stud of the carb to the vacuum booster. Thanks Bob
  14. sxer

    dash pad cover

    Has anyone found a dash pad cover that they like? Mine is cracked pretty bad but don't really want to spend what it costs for a new one. Thanks Bob
  15. sxer

    Change lube in SR 4

    This is probably a stupid question, but how do you change the lube in an SR 4 transmission? I can't find a drain plug in the bottom, but there looks like there is a boss where a a hole could be drilled and tapped for a pipe plug. It is mated to the 300 transfer case in my '81 scrambler. What is...
  16. sxer

    Homemade console

    Here are some pictures of a console that I made from MDF and had covered. It works very well. It keeps the radio from getting wet and provides an arm rest. I ran the wires in some plastic flexible conduit across the floor on the side of the hump to under the dash. I have a drawing and the...
  17. sxer

    Need Help

    Not too long ago someone posted an excellent picture of the gas tank with all the connections labeled. I thought I printed it but of course now I can't find it. Does anyone remember it? I tried searching but couldn't find it. Thanks Bob
  18. sxer

    My rebuild

    I am doing a frame off rebuild of my '81 Scrambler. I plan on keeping the Jeep for a long time so my main goal is to kill the rust as well as possible. I am not making a show truck out of it. I will be doing almost all the work myself to keep the cost down. I have had it apart for over a year...
  19. sxer

    speedi sleeve

    If your front seal is leaking and the seal lip has worn a groove in the balancer, it is much cheaper to install a speedi sleeve than to buy a new balancer. I bought mine at NAPA for around $26.00 for the 4.2L engine. It is a very easy install. Bob
  20. sxer

    Can't figure this out

    I have a situation on my '81 Scrambler that is really bugging me. I have a 4.2L engine and what I think is all stock transmission, transfer, and differentials. The drivers side rear tire tracks about 2" inside the front tire. On the passenger side the rear tire tracks directly in line with the...
Top