• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. C

    Glove box lock fix

    I also marked the location of the retaining pin on the new knob shaft, and filed an indent so I could put the retaining pin back in cylinder around the new knob shaft. Like this:
  2. C

    Glove box lock fix

    I removed lock pins, including retaining pin for cylinder. Only retaining pin is shown in this picture: Then I measured depth of lock cylinder. Cut new knob to length. Then filed the point of the triangle so the shaft would fit snugly in key slot and press to bottom of lock cylinder.
  3. C

    Glove box lock fix

    Now you have this: And I bought one of these headlight knobs for $4 to put on it.
  4. C

    Glove box lock fix

    Use the end of a small cotter pin in the hole on top of the housing to press down the lock pins and remove cylinder.
  5. C

    Glove box lock fix

    So, I had a locking glove box latch, like this: But the handle was gone when I got the jeep. Only the lock/cylinder was left. And it didn't work well that way. I wanted to be able to open the glove box and didn't want to spend $30 or $40 to fix it. Here is what I did.l
  6. C

    Low budget engine/drivetrain swap

    The older xj has a different EFI controller. Rather than Chrysler it is Renix. Still a multiport system but has less power. If you search it up it seems to work ok. Most of those years will also have the Peugot transmission which is ok if you aren't going to beat on it much or bump up the...
  7. C

    Side Mirrors shake so bad i can't see...

    I welded a small piece of 16 ga to the flat side of the aftermarket arm to beef it up. Helped a good bit with wiggle/twist in the wind.
  8. C

    Small block ford swap

    Sounds like you are good for ignition. On engine - The 5.8 you are looking at, both year blocks you have actually, are relatively low compression. The 97 if stock will have hypereutectic pistons, and compression is like in the high 8's. Unless someone changed it, the cam in the 97 block is...
  9. C

    Small block ford swap

    Those roller blocks live long lives if they are even sort of taken care of. So, good news for you. Your 85 block bored at .060" over is pretty much bored to the max it can be, and sometimes they have heating issues when at that dimension. So I think you are going the right way even with 76k...
  10. C

    Small block ford swap

    I did not have to change driveshafts because of the motor mounts at all. I did it because my overall driveline became about 3 inches longer relative to a fixed point I picked on the frame. So I likely would have HAD to address front shaft length. But my rear would have probably been OK. But...
  11. C

    Small block ford swap

    The Contour fans are a great option when you get that far. The stock mechanical fan will hang below the radiator, and on mine it hung below the front cross member too.
  12. C

    Small block ford swap

    Overview look at fit. You can see there is plenty-o-room on passenger side
  13. C

    Small block ford swap

    I used these: http://www.summitracing.com/parts/sum-g9035/overview/ which are for a late 80s - early 90s f-series 5.0 They come in a summit box, but are made by pacesetter. They have 5.8 specific set also. It appears only the passenger side is different, which is not where I had issues anyhow...
  14. C

    Small block ford swap

    If you say so... I don't know of the top of my head. It makes sense since the SR (and the T4/5 trannys) has looooong tail housing that holds the shifter. I would think the t18 would be even shorter than that. But if you use a clock ring between tranny and transfer you will add an inch-ish...
  15. C

    Small block ford swap

    That is true. You would need an adaptor at the bellhousing. But you would not need one at the transfer case. Plus you get the steep first gear (4. something to 1 instead of 6. something...) in addition to OD. But I think your plan is solid and should go together well.
  16. C

    Small block ford swap

    You probably thought about them.. what did you some up with on 5 spd trannys? You really cant beat $100 for the t-18, but no overdrive. I have about $300 into my nv3550 including rebuild. And I could have re-drilled the flange to mount the d300 and not needed an adaptor of any kind for the...
  17. C

    Small block ford swap

    I think some did come hydraulic, but mine wasn't. Not sure what the combo or year would have needed to be; mine stock was an 84 Laredo 4.2 with t5/Dana300. The driveshaft was a problem at the transmission flange and the bellhousing. I didn't fully compress the springs to see if it would hit...
  18. C

    Small block ford swap

    Since I cant figure out how to edit... If you don't plan to wheel this rig hard, why use a t-18? Have you driven one before? They are a for real truck transmission and act accordingly in terms of shift length, speed and smoothness. The SR4 will not last behind a 5.8, but the jeep t-150 would...
  19. C

    Small block ford swap

    Oh yea... Oil pan. You can use the truck pan, it will fit no problem. They usually have large rear sump with small front sump (2 drain plugs). Unless you have something I never saw before, which is possible.... Radiator I am using a stock 3 core with Ford Contour fans and a 195 thermostat...
  20. C

    Small block ford swap

    I just did this swap. But I used the Ford EFI and an nv3550 I rebuilt. Ask away, I can take pictures of whatever you want. My opinion on a few things you mentioned: 1. engine mounts. I made a set first, placing engine in "stock" location so I could keep all stock skid plate, transmission...
Back
Top