• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Jon also includes a nice wear strip where the top crosses the w/s frame.
  2. surfjeepzx

    Any Las Vegas members that can lend a hand?

    I think this was an early pic with the slight downward angle to the rear half. I hadn't started playing with applying pressure to the straps. While I was outside messing around they fired a rocket from the Cape. You can see the white smoke trail in the upper right corner of the pic
  3. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Here's a close up of the nylon deck mount. Assembled, the set screw on the pipe end screws down almost flush.
  4. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Here's the rear side strap I came up with. Using a nylon strap eye and a plastic swivel to shorten the rig. I'll need to sew the strap and trim off the excess when complete
  5. surfjeepzx

    Any Las Vegas members that can lend a hand?

    The foam helps soften the curves and relax the fabric.
  6. surfjeepzx

    Any Las Vegas members that can lend a hand?

    I didn't want to mount the footman loops on the upper edge of the tub so I recessed them to this point. Then I modified and reversed the strap so the loop end is secured in the footman loop which results in only one straight run of strap material exposed to the wind. The tag end is then pulled...
  7. surfjeepzx

    Any Las Vegas members that can lend a hand?

    I think in order to use the longer top and keep the bow above the tonneau would require the feet to be mounted to the rollbar. That would result in too severe an angle on the bow which would cause the bow to lay down. The length of the top dictates the angle of the bow to body. The tonneau...
  8. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Surfari bow Here is the bow I made. You can see the sharpie lines at each end of the bends and the center mark. Also the rubber feet are installed. The rubber feet grip so the bow can be repositioned.
  9. surfjeepzx

    Any Las Vegas members that can lend a hand?

    If he did I'm sure they would be nice. If fabric was more affordable he could color match the original Nutmeg and order a roll. That would change everything!
  10. surfjeepzx

    Any Las Vegas members that can lend a hand?

    We talked about the batons but the length of the CJ-8 top exceeds the baton length he has so we decided to proceed without. Also I was kind of pressed for time as this week starts JeepBeach here in Daytona and I wanted the top in place for cruising with my family.
  11. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Since you're out west I can pick up the marine grade stuff here and mail it to you. When you get it just send me a check. I would also "fit" the pipe into the vinyl pipe ends as they're a little tight and require some heat to resize the pipe ends. We're mixing stuff that wasn't designed to go...
  12. surfjeepzx

    Any Las Vegas members that can lend a hand?

    I can think of several ways to do that but it depends on how willing you are to be creative in finding mounting points for the bow. They could be mounted to the top edge of the tub similar to how a traditional soft top bow is located. The bikini is narrower than the full soft top so the bow...
  13. surfjeepzx

    Any Las Vegas members that can lend a hand?

    I haven't driven it yet. Getting tags on Monday and it will get the ops check. The material is a much heavier gauge than Best top stuff. The straps Jon uses are better than any high end marine grade stuff I've seen. You can see attention to detail everywhere you look. I don't anticipate...
  14. surfjeepzx

    The beginning.. the end.... and a fresh start

    With alcohol sprayers for the sidewalk clearing night time flame effects. :headbang:
  15. surfjeepzx

    The beginning.. the end.... and a fresh start

    That looks better than squaring them off behind the wheel too. I think they would look even better if you took a saws all and slant cut them back a tad.
  16. surfjeepzx

    The beginning.. the end.... and a fresh start

    More Safari top stuff Yesterday I spent more time on the Safari top. The top was designed to have a slight downward pitch to the rear portion past the rollbar. I raised the rear section to near level and like that look better. Then I installed the marine style bimini top mounts and fitted...
  17. surfjeepzx

    Any Las Vegas members that can lend a hand?

    Here it is almost done. I'm still tweaking the rear bow height. The top was designed to have a slight drop to the rear section but I like the level look. I had it mocked up both ways and prefer this lay out.
  18. surfjeepzx

    The beginning.. the end.... and a fresh start

    I've seen CJ's with rear exits and I never really thought they looked right. The Scrambler with it's longer bed and a lift will show the pipes all the way out the rear and IMO, wont look good. I've always rolled my Jeep out of the garage before firing it just so I don't have the fumes in the...
  19. surfjeepzx

    The beginning.. the end.... and a fresh start

    I'm very pleased with the exhaust. I placed the brackets on top because I kept the system up tight and within the frame rails. I didn't originally plan to place the mounts above the standoffs but once the system was mocked up there wasn't enough clearance to mount the isolator below the...
Back
Top