Search results

I purchased a D60 with -501 embossed on the top of the carrier housing. The axle came out of a Rock Crawl CJ7 Laredo that was in a garage or carport fire, burned from the top down, so the drive train was in good condition. I also bought the D30 front axle w/4.88 gears and a lunch box locker...

Anyone have, or know where I can find the plastic "?" shaped wire harness protector? This is not the harness loom. This is a plastic piece that screws to the bottom lip of the wheel well in the left rear. This piece keeps the harness that exits the interior, runs along the lower edge if the...

Has anyone seen the new Edelbrock Aluminum head designed for the 4.0L and 4.2L engines. Going through CARB cert right now. Looks like HESCO has a little (oops,Huge) competition in the Aluminum head arena. Hopefully this will bring down the price some what.

Just wondering if anyone has ever tried to adapt Dana 30/44 front locking hubs to a rear axle. A new mounting plate, some axle seals like the aftermarket front ones, and some custom axles. Just thinkin'

I just finished the install of a DRL (Daytime Running Light) module in my '81 Scrambler. Works great, no more dead batteries due to leaving the headlight switch on. During the day, only the headlights come on. There is a photo sensor mounted on the bracket that holds the VIN plate that...

Is the bell housing bolt pattern on a 2005 6 speed the same as a T-5 trans bell housing? I want to install a six speed in my 8.

Does anyone have dimensions for the CJ dash overlay? I mock'd one up in Catia and want to verify the corner radius' and the hole sizes znd placements. The top radius looks to be around 2" while the bottom one's look to be an inch or so. I am looking to 3D print the finished design, so if anyone...

Does anyone know the width of a JK tub at the rear vs. a CJ width? I am just wondering if a Rock hard parts JK rear bumper is too wide for a CJ. Thanks.

How is this for a custom look for a CJ? Similar gauge arrangement as a YJ i.e. Tach on left of column, smaller spedo on the right, folowed by Fuel, Temp, Clock, Oil, and then volt. The colored pod above the steering column contains the L/R Blinkers, 4wheel Drive, E Brake, and High Beam...

Has anyone ever made any rear passenger side panels, similar to door panels? They could velcro in when the top is off, and be re installed when a full top is on. How about a carpet/vinyl combo similar to a Laredo door panel.

I have a question about the clamps that mount the ACME full length hard top to the "8" (I have new correct locking clamps). Is there some sort of backing buried in the fiberglass that the screws/pop rivets anchor to? Or are you just screwing/drilling into fiberglass? I haven't tried a magnet...

You sell this....... To buy this... and one of these, but get 2 for the price of one (IVF) Katelyn Ryan

I had the cam go out on my '81 4.2, so after replacing the cam, chain, gears, and lifters I decided to do a Mopar MPFI conversion along with a 4.0 Head conversion. Now I have a dead cylinder. First it was #5, now 5 is good and #6 is dead. This is what I have checked so far; Plugs, swapped...

Hello all, Does anyone have a source for the engine wire harness 2-pc. bulk head connector for an '81 CJ-7/8? Even a blank used one (without the 31 years of dried tar) will do. Thanks. 1981 CJ-8 California, 4" BDS lift, 33x10.5x15, 4.2L, 4.0L head, MPFI, 4.11, full HT, full Roll Cage.

Hi all, I just recently upgraded my '81 "8" to a 4.0L head and Mopar MPFI. Still working on other issues with fuel plumbing, so the 8 is not running yet. I wanted to pass on an upgrade that (in my opinion) is a super idea when doing the MPI upgrade. This does not apply to a Howell upgrade...

I am looking for a bolt on grill guard for the stock bumper. Smittybilt and Hobrecht made these back in the 80's, but the ones I see today are bolt together. I am looking for the all welded 3" dia tubed 1/4" thick side plate guard. If anyone has one they can part with I may be interested. Here...

Does anyone have a .dxf or .pdf of the left and right AMC Model 20 disk brake caliper brackets that use either the Suzuki or Cadillac calipers? I can create a CAD file and export the file as a .step file for any machine shop to CNC these brackets. Is there also a spacer drawing for the backing...

Does anyone know a source (or part number) for an OEM style ignition coil connector for a 1993 4.0L? I accidently broke mine while converting my 8 to the Mopar MPFI kit. The wire harness connector is the square type with the blade connectors. Dealer has this part as discontinued. If you have an...

All, I am looking for the serpentine belt idler pulley and bracket that replaced the smog pump on a 4.2L. I converted to Mopar FI and a 4.0 head and cannot reinstall the smog pump (to use as an idler pulley) because of a fuel rail / smog pump interference. If anyone has this complete assembly I...

Will a CJ 7 main hoop (with the legs removed) bolt into a CJ 8 (with the bolted in braces where the "7" hoop bolts to the tub removed). I want to use a "7" main hoop for a full cage I am planning for my "8". Thanks in advance fo any answers to this question.