• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. C

    Exhaust routing with a 20 Gallon n tank?

    zr.. Did you go inside the shackles on the back? With my 20 gal tank, they practically touch the sides of the tank skid. Mine looks like yours, but turns out the sides at a 45 like stock at the back.
  2. C

    Exhaust routing with a 20 Gallon n tank?

    Dain.. I have a full exhaust from the 258 I removed and sold, exhaust manifold to tailpipe (minus the cat conv), that you can have if you want to pick it up. Previous owner had revently replaced it so it is still all shiny clean galvanized looking after the manifold. I was thinking about...
  3. C

    Epic fails

    Well.... It only makes sense that if you are going to use metal shavings to put racing stripes around all the bearing journals on your crank, that you use shavings FROM the crank. Right??
  4. C

    Small block ford swap

    Gt40, or gt40p? Either is nice, and an improvement over what would have come on either block you have from factory. Plug angle is biggest difference between the 40 and 40p, but it can affect what headers you need. Is it the 258 cam with 1300-5300rpm range with .533 lift? If so I have been...
  5. C

    buying a radiator

    They get additional cooling area by using larger tubes/more fins, not by making the radiator bigger. Read about this in Hot Rod or the like, don't remember exactly... Copper-brass is a better heat conductor material than aluminum. That is the material science. But then, construction and...
  6. C

    Help! Weber carb 2nd stage flat spot..

    You can also look here: http://www.carburetion.com/Weber/adjust.htm or here: http://www.yotatech.com/f120/proper-only-right-way-tune-weber-32-36-a-240521/ I talked to an MG enthusiast friend of mine and he suggested these links.
  7. C

    Potent gas smell

    And when you look at your canister, chances are the purge valve will be bad. Don't spent $100 on canister because you cant rebuild the valve on the stock one. Do this instead: Here is the Delco part number: CV10042 It is about $6 instead of $100 for a new can with correct...
  8. C

    Potent gas smell

    If you haven't changed your fuel lines in a few years, start there. The ethanol in gas now eats fuel line of the past over time. If no leaks there, I would check evaporative system next. Ie; tank vent, charcoal canister, etc...
  9. C

    Good carbs for a 258 with the 4.0L head?

    According to the Ford Carburetor Guide from Pony Carburetors, flow figures for the Autolite 2100 carbs are as follows: .98 venturi = 190cfm 1.01 = 245 1.02 = 240 1.08 = 287 1.14 = 300 1.21 = 351 1.23 = 356 1.33 = 424 So even up to a 1.21 would work ok, particularly if you had...
  10. C

    Help! Weber carb 2nd stage flat spot..

    Is it backfiring out of carb? If so, and you know your timing is right and it doesn't smell like a rich fuel mixture, I would be looking at float level maybe being too low.
  11. C

    Good carbs for a 258 with the 4.0L head?

    Since you asked for comments on Webers... I have never used one on a car, but have had them on motorcycles. Both down and side draft varieties. They ran great when I had them tuned right. But they liked to have a lot of attention paid to them or they didn't stay tuned right.
  12. C

    Power Steering fluid Leak

    It means it takes 4 turns of steering wheel to go from all the way left to all the way right.
  13. C

    Power Steering fluid Leak

    Ok.. Lets back up a bit. As information: Most of the components like steering columns, steering gear box, brake master cylinders, etc.. on our Jeeps are "off the shelf" parts that AMC bought form GM or Ford or whoever, and used in Jeeps. The steering box in our Jeeps from factory is a Saginaw...
  14. C

    Good carbs for a 258 with the 4.0L head?

    I am a fan of the Motorcraft 2100. Specifically with the 1.08 venturi and electric choke. Mine ran best with #47 jets.
  15. C

    Power Steering fluid Leak

    I had a similar leak after my engine swap. A minor seal kit was $15. A major seal kit was $100 A rebuilt unit was $140 after core fee at AutoZone. This is what I ended up doing and so far it is fine if the 4 turn ratio doesn't bother you. I have also used West Texas Offroad in the past when I...
  16. C

    Small block ford swap

    It is a D20 twin. That was on a "J" pattern d20 so putting on twin sticks is about the same as putting them on a d300. The "T" pattern d20 is a bit more work to twin, hence the "custom" Hurst handle mod.
  17. C

    Small block ford swap

    Sorry about this part in above post. It was some of my initial thoughts before I figured out how to use pictures to tell the story better. I really need to figure out how to edit posts....
  18. C

    Small block ford swap

    I have never put a zf in a jeep, but I have done a couple in old broncos. I have done nv3550 in old broncos and now in a jeep too. So, lets compare. Here is a zf in a bronco: Here is a nv3550 in bronco: You can see that the zf tower (without shifter base) is 2x the size and comes up very...
  19. C

    Small block ford swap

    That stinks. I am not sure I would trust a weld on cast iron from a bearing surface around to next corner. That is a bit much. The zf is also about 3 inches taller. You would need a body lift and/or get pretty creative in floor cutting and tunnel cover making to cover the shift tower, and may...
  20. C

    Glove box lock fix

    Then I put some Permatex metal repair epoxy in the pin slots top and bottom to make sure things stay put. You can see I stopped short of the retaining pin. So the retaining pin moves up and down on the tiny spring like it should, meaning you can install/remove the cylinder to the lock base...
Back
Top