• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. hefavitzen

    Interesting Light Question - 4 separate filaments or bulbs

    Can you legally run these on a Jeep in the US???? I live in South Carolina and we don't even require annual inspections. Anyone have issues running these lights on the street?
  2. hefavitzen

    Recommendation for bump stops on 2-1/2" BDS lifted Jeep Scrambler widetrack

    Anyone ever install Timbren bump stops? They are really pricy (about $300 a set) but video looks nice and cushy.
  3. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    Ah, so, when I say "11 inch lbs" I mean that with the axle under the jeep, the wheels and brake rotors removed, that the yoke took 11 inch lbs to rotate, including having to rotate the ring gear and axle shafts. I can certainly try to tighten it all up more, which I assume will force the...
  4. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    Thanks! I'm going to go look that up right now. I actually have a full Yukon AMC20 rebuild kit that I might just end up putting to use.
  5. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    It felt fine (I think) with no play to speak of, taking about 11 inch lbs of force to turn the yoke with the wheels and brakes removed. I actually tightened it up as much as I could by hand (instead of using an impact gun) as I had read that it could growl from not being tight enough. It was...
  6. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    Heck if I know. It won't surprise me if they are complete garbage. I've put at least 1000 miles on the rear end since I put it in and it does a little growling, but it moves and hasn't blown up yet. Question for you...how would you tell? The pinion doesn't have any slop, if that would be...
  7. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    Another thing: When I put the new yoke on it was a VERY tight fit to get it on initially, but then "popped" on the rest of the way with a tap from the dead blow hammer. I then put the new pinion nut on and couldn't get it tight enough. (see video below). So, I took it off and put the old...
  8. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    So, I compared the old and new seal and found quite a bit of difference. But, in the end, I could not get the new seal to fit. As you can see in the photos, the first two seal have a metal outer edge so it has to has to go in very gently. Looking at the last photo, of the rubber edged seal...
  9. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    So, once I got under my Jeep I marked the pinion, nut, yoke and diff for a line up reference. - it took 15 turns to remove the nut. - the yoke popped right off with just me pulling on it with my hand. - As you can see, the seal was in place, but the rubber gasket had torn. I replaced the pinion...
  10. hefavitzen

    AMC 20 Pinion Seal - Yoke Replacement

    I wanted to provide what I found through trial and error when replacing my pinion seal and the yoke. I had replaced the rear AMC 20 last year with a used wide-track, just before heading up to the Silverlakes meet up. You might remember that I had asked if I could get away with having one of...
  11. hefavitzen

    Virginia 4 Wheel Drive Association’s Fall Run

    Hey guys, how "difficult" will the trails here be? I might have my Scrambler back in one piece by this time and I'd love to do another event. My wife was even saying she wanted to go back to Silver Lakes again with the group. Do you camp at this event or do you get a hotel? Are the trails...
  12. hefavitzen

    SBC 350.. starting issues

    Here are some ideas: 1) Choke - do you have an electric choke and is it stuck closed? 2) Not sure what kind of carb you have but there are TONS of videos about how to tweak carbs on the U-Tubes. Check out Thunderhead289's vids. I'm thinking maybe some debris in the accelerator pump, out of...
  13. hefavitzen

    AX-15 Sources?

    Ha! That is about on par with my luck. :) If you get any more, give me a ping.
  14. hefavitzen

    AX-15 Sources?

    Hey guys, anyone have a good source for AX15 Transmissions? My TH350 has begun eating it's clutches and I would like to convert back to a manual. Usually the AX15 is about $1700 new (Novak / Advanced Adapters) but so far everyone I have called has no idea where the transmissions are or when...
  15. hefavitzen

    Installing the fenders - any tips?

    Hey, what motor mounts are you using? Your engine is sitting nice and low. Just curious! :)
  16. hefavitzen

    My Newest Project - Me !?!?

    Holy smokes I'm so glad you are going to be 100%! Paying attention to your health and doing reasonably frequent inspections is super important!
  17. hefavitzen

    82 Scrambler Build

    A few questions: How do you like the magnaflows sound and do you have heat shields between them and the floor? I ask because I have glasspacks I'd like to replace, and have been thinking about Magnaflows, and that the glass packs make the floor very very hot!!!! Too hot to put your feet on...
  18. hefavitzen

    Upper A-pillar repair panel

    I'd like to know too!
  19. hefavitzen

    Dune Cat - Go Cart - Anyone interested in this?

    Duneit - I found his contact information and have PM'ed you with it!
  20. hefavitzen

    Dune Cat - Go Cart - Anyone interested in this?

    Hey Duneit! I apologize for not getting back to you sooner! I have been combing my hard drive and online storage and haven't found this guys contact information that I spoke to. I did find the link where he posted information about them, but it is no longer working. HOWEVER, close by in...
Back
Top