Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
Do you guys trim the gasket so that it fits the port perfectly? These hang over the edge just a little on the center divider. I was thinking about trimming it down a little to fit though I am a little nervous about screwing it up. ha :)
Ok, so here are the Fel-Pro 1255 / Edelbrock 7235 gaskets on the Chevy Performance Vortec heads and the Edelbrock manifold. As you can see, this is a MUCH closer fit than the other gaskets. Oddly, these two gaskets are identical and both are composite and the only gaskets I could find that...
I agree, there is a LOT of room on the outside of each port.
Here is a screenshot of a Fel-Pro 1255. As you can see, the ports are canted just like the heads ports are. This looks like a much better fit, though it is a composite gasket. Summit has good ratings for it.
As you can see, the...
Here is the new gasket on the head and on the intake. The gasket, as mounted on the head, has little nubs that fit into holes in the head to put the gasket in the correct position. The gasket doesn't pass the edge of the intake port center section, but it is right on the edge. Sure is a lot...
Ok, so work on the intake gasket is progressing.
I removed the intake and found that the gaskets that were used were not the composite gaskets I imagined, but were actually plastic over metal.
Part I am replacing: Chevy Performance 89017465
I am putting on the gaskets from the FEL-PRO MS...
I am positive I have run of the mill heads and have ordered a Fel-Pro set. I'll take some pics of the whole operation as I pull the intake, looking for obvious issues and check the gasket fitment and putting it back together praying it fixes the problem. Gaskets should be here today so more to...
So what if I cannot find gaskets who's ports are the correct size? The Edelbrock Performer 21163 Intake instructions "recommended gasket" has a Port size of 1.08 x 2.11
Here is a screenshot of the instructions for the manifold that state the port size:
I'll try these! I hope that is all it is. :) I looked back at some emails with the place that built my engine and I had brought this issue up back in 2015 but we couldn't figure it out. I am way too nice and just lived with it thinking, "maybe this is ok?" Ugh. I wish I had brought this up...
I did change the spark plugs before I did all of the diagnostics I listed out. The photo is the set I pulled out, not the set I put back in. The new set though does show fouling of the #8 plug even with only about 10 miles of driving.
I've been dreading actually having to dig into the head...
I keep coming back to maybe it is the valve guides that are worn out on the #8 cylinder on the new heads that were installed in 2015.
If that is the case, how can you tell without pulling the head? I'd like to avoid pulling the head if possible since it doesn't leak at the moment. :) I am...
What I am fighting today:
Two years ago(?!?!?) when I came up to the Sand Blast event, a few of you pointed out that my ride was smoking and you were not wrong! In fact, I had F'ed the timing up something fierce and just hadn't realized it yet. So, I've been working on that and have some...
Hey guys, It has been a while since my last post but a lot has been going on. Besides the family growing and kids getting older and more active, my Jeep project has also continued on.
Two years ago(?!?!?) when I came up to the Sand Blast event, a few of you pointed out that my ride was smoking...
Hey there, how much do you torque the shackle bolts down? My manual says 24lbs, but that is for a stock shackle. I have OME YJ springs and shackles with greasable bushings / zerks and at least one of my front shackles is a tiny bit angled. I'm thinking I have my shackle bolts too lose but...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.