• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. gaducker

    one piece axel?

    I got the bearings on and when its tight its hard to turn, not impossible just stiff. I drove it home and that side is warmer than the other. My question is how is preload set? I don't have any shims in it and the block in between the spider gears is still there. I suspect this is what...
  2. gaducker

    Bumper End Caps

    Whats the thickness of these parts? A 5 gal bucket is roughly .095 to .125 through out. And with hdpe you can fill a 5 gal bucket and drop it from 8 feet and the bottom wont split. You can get regrind hdpe CHEAP and throw in some uv additive and bam cheap and tough
  3. gaducker

    Should I get excited about this?

    Being 2wd wont matter cut all the coil buckets off and SAS it. I would say if the frame will fit and you can work out the mounts then theres half or more of the battle. A SAS is simple when you have a set of clean frame rails to work with.
  4. gaducker

    Bumper End Caps

    How about a 3d printer?? Is that what a rapid prototype is?
  5. gaducker

    Bumper End Caps

    I worked in the injection molding industry for 10 years as a mold and die tech, And yes these are some small parts but the mold is going to be very expensive if you water cool it and install air poppets and all that stuff that's required to run hot material. Having worked in the field I would...
  6. gaducker

    amc 20 ?

    I found it , Timken part number "set 9"
  7. gaducker

    amc 20 ?

    Anybody got a part number for the outer bearing when running one piece axles??? I got a lock ring but have had no luck finding a part number with what pieces I had left over.
  8. gaducker

    Should I get excited about this?

    Anything will fit with enough torch, plasma and grinding wheels. Get you an old ford f250 frame and use that.
  9. gaducker

    I am lucky my scram broke yesterday.

    ouch!!!!!!!
  10. gaducker

    I am lucky my scram broke yesterday.

    Oh yea there was plenty of knots on my head already but this one was as big as a golf ball, no lie. It was just above my eyebrow and stuck out 2 inches, I could see my eyebrow for with out trying for two days.
  11. gaducker

    I am lucky my scram broke yesterday.

    As long as they dont try and fix her car that may be what I try to do, Just let her drive the cummins and I will start over and build another one.
  12. gaducker

    100 day summer rebuild

    Get at it!!!!!!!!!!!!!
  13. gaducker

    RE 4.5" lift belly height?

    Oh and mines got a shackel reversal with a little bit of shakle lift.
  14. gaducker

    RE 4.5" lift belly height?

    Mines 24 inches just behind the rear spring hanger on the front spring, with a 4 1/2 rubicon express lift and 35 inch cooper stts.
  15. gaducker

    82 4bt build

    Good to see you back, I was just wondering the other day how your jeep was coming along.
  16. gaducker

    Should I get excited about this?

    This one was just a tug frame that was extended with 6 inch channel and a bed was stick built out of square tubeing and sheet metal. https://www.cj-8.com/forum/showthread.php?41018-cj-10-That-I-have-had-my-hand-on&highlight=
  17. gaducker

    one piece axel?

    I dont remember what maker it was, I just ordered a single side repair kit and hope its the same, SInce its the same bearing in most I would think the id of the lock ring would be the same as the bearing which would also be the same from axle to axle??? NO??????
  18. gaducker

    I am lucky my scram broke yesterday.

    Yes everyone is ok, just my beat up knees, cut head from glasses and a big knot on my head.
  19. gaducker

    I am lucky my scram broke yesterday.

    Since finishing my jeep I have been driving it daily, Well yesterday the outer bearing started singing and I took it apart at work during the day thinking I could put it back together and roll on home but it didnt work out and I left it at the shop on jack stands. My daughter is in the band...
  20. gaducker

    one piece axel?

    So i put one piece axels in when i first got the jeep, have not had a problem till this morning, it seems the taper bearing ate itsself up from the outside in. Now???? Where do i get new bearings and a lock ring? Or is it just a stock bearing ans can i heat the lock ring off nd reuse it?
Back
Top