• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. C

    Factory fogs - need wiring help please

    In OEM form: The switch pulls power from the dimmer switch circuit on the grey wire, so it can only work when low beams are on. The red/trace goes to ground and one side of relay coil. I know its weird, but that is what diagram says. Dark blue is switched and goes to other side of relay coil...
  2. C

    D300 speedo gear replacement - but on an '81

    Measure the output shaft housing from main case. If it is 3 1/2 -ish inches long it is short version. If it is 5 1/2 -ish inches long it is long version. If you have short version, I think it uses same drive and driven gears as the Dana 20 and 18 cases.
  3. C

    How I internalized my fuel-related issues

    Something I forgot to mention on this re-fit is that it is possible to use the fuel level sender included on the overall assembly if you want. The resistance range is different than that of a stock Jeep gauge, but if you are planning to use an aftermarket gauge in the more common 240 - 33 ohm...
  4. C

    Seat Dimension

    Could someone grab a measurement for me? I need to know the height of the sitting surface of a stock seat. A measurement from floor just inside door to seating surface at rear and at front would be perfect. I cant find the dimension sketch I made before I removed and sold the stock seats from...
  5. C

    How I internalized my fuel-related issues

    Whoops. forgot to delete that last bit.... its repetitive.
  6. C

    How I internalized my fuel-related issues

    Speig - I missed your question on leaking. The seal shown with the hole saw is what came with the assembly. The 4 inch hole allows this to slide in and reach below the flange inside the tank. That is why size, roundness and smoothness is important, it affects sealing. When you press the cap...
  7. C

    Fuel gauge Voltage Regulator BYPASS

    Well, not exactly a bypass. But close. I don't like the temperature based VR. It works, it is simple, and I give full marks for clever on its design. The problem I have with it, is that nobody makes a new one that lasts more than 3 months anymore. And I was tired of contact surface...
  8. C

    Fuel guage not working.

    They shouldn't all be hot, as in have 12v on them relative to ground. If so that is a problem. At the gauge: The red one (usually its red) will be 12v from battery system. The pink one (usually pink) will be the wire from your tank sender. This one is variable resistance relative to ground...
  9. C

    How I internalized my fuel-related issues

    Mysunnshine - yes, MPFI drove this solution. This particular installation is feeding a 331 Ford. I suppose you could swap the pump in the cup out to something else if you wanted lower system pressure. Generally speaking, the assembly is what makes the idea work and you could use other pumps...
  10. C

    Spankrjs' 1984 Long Term Project

    Spankr's - All those things will help. And I know some Bronco guys that have been running port EFI for a long time using those low pressure into reservoir- high pressure to rail set ups. They work fine, you just have 2 pumps instead of one. In most stock tank set ups they offer some good...
  11. C

    How I internalized my fuel-related issues

    And, it works great. No pump noise. No more pressure variations. And it will run the tank down far enough so you have to pump 19.2 gallons into it. (That was an accident, I didn't test on purpose. Your results may vary) And for off-roading, I have not had fuel pick-up trouble in steep angle...
  12. C

    How I internalized my fuel-related issues

    And, last - a few things I did that you may do, but don't have to. Cut hose control loop off the tank strap. I wanted the inlet/outlet of the assembly to face the way it does in picture due to where I wanted to mount my post pump filter and still have enough hose to drop tank without unhooking...
  13. C

    How I internalized my fuel-related issues

    Now, to mount and seal this sucker. In a GM application, there is a steel flange molded into the top of the tank where they put the pump. The steel flange has screws, ramped teeth, or wedge locks around its perimeter. The assembly sits in the middle and a second locking ring goes over the...
  14. C

    How I internalized my fuel-related issues

    And, once you drill the hole your assembly will slide in there like it was made for the purpose. The cup will sit on the floor of the tank flat on its feet. The offset flat where the gauge sender is mounted on the assembly allows the cup to sit just inside the sump edge. And you have about 1...
  15. C

    How I internalized my fuel-related issues

    So, to reach the bottom of the sump, and have room for the cup to sit flat in the sump; this is where you drill the 4 inch hole.
  16. C

    How I internalized my fuel-related issues

    Ok.. picture worked... These are available from junkyards anywhere. Or new from Carter, Delphi, AC Delco, Walboro, Airtex, and others. The one for the mid 2000's GM truck works well because it is the right height for our tanks without modification. The cup sits on bottom of tank on the feet...
  17. C

    How I internalized my fuel-related issues

    This is the fuel sender assembly I am referring to. I will show some pictures of the internals if you want, but there are lots on internet already. Basically, this thing puts the fuel pump down into the cup at the bottom of the assembly. The pump has an intake sock in the cup. The cup holds...
  18. C

    How I internalized my fuel-related issues

    Huh... I guess I will have to come back later and finish when the site will take a url or direct upload picture.
  19. C

    How I internalized my fuel-related issues

    Have been reading Spankrj's thread where he talked about fuel problems. So I thought I would Share how I put an OEM fuel delivery unit from a mid 2000's chevy pickup into one of our original Jeep 20 gallon plastic tanks. I have done this 3 times now. The oldest installation has been working for...
  20. C

    Spankrjs' 1984 Long Term Project

    A secondary reservoir works and is a popular DIY solution for older cars with newer fuel injection systems. Here is an off the shelf version of what you describe...
Back
Top