Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
I would like to know exactly what I need to finish my Dana 44 front in my plow truck.
I have a narrowed housing I got from Crossbones years ago,
Using Dana 44 Jeep knuckes what else do I need:
Spindle?
hub and rotor?
Caliper bracker?
Caliper?
What would a mint set for front CJ Laredo seats go for?
I am speaking of the black ones with the silver stripes, mint condition with carpet of the side
Does anyone here have experience with the Hydraulic clutch set up conversion for the CJ? I am using Parts MIke master and slave. Is there a trick to bleeding this? I am not getting the fork travel I need.
I need to install a steering shaft on my CJ 7 project. Since I am using a J-20 box I was wondering if I need to order a special lower joint since i think the J-20 box has a different spline count. Anyone know for sure?
Anyone recommend a shaft? Flaming River, Borgeson, ???
OK so it's not a Scrambler project, rather a CJ 7 build but I need some opinions. I am building a monster CJ7. Has a 401, Dana 60's and 37's. I was going to use a monster Clark 285 5 speed but I want to change to an automatic.
QUESTION: my first thought is to use a 727 and a dana 300. will...
I need to fab a steering shaft for my CJ 7. It has a J-20 box andf a stock CJ column. What manufacturer makes the best kit? I remember Grantshire had one on his project.
Is it true that there are differences in the steering box spline size?
I am looking for a source for weld on lower shock mounts that are similar to the front Dana 44 style. Most of the ones I am finding are straight, the front Dana 44 are angled. I have a Front Dana 44 with a damaged lower shock mount that I need to replace.....
In Order To Get The Pinion Angle Right I Needed To Rotate My Rear Dana 60 Quite A Bit. I Am Running A Tom Woods Rear 1 Ton Shaft With 1350 Joints And Cv. To Properly Set The Rear Pinion Parallel With The Shaft I Need To Rotate The Housing A Lot. Did Not Measure But It Looks Like The Pinion...
Anyone running Hummer H2 wheels? I am using them but ran into a problem selecting the correct lug nuts. The factory H2 uses a metric 14 m x 1.5 thread stud. My Dana axles have the standard 9/16 x 18 thread stud. I want to make sure I use the right lug to properly seat the wheel. I believe...
Boy am I asking a lot of questions today or what!!!!!!!!
Does any one know who makes a hydraulic clutch conversion for the CJ series? Are they of decent quality??
Anyone done either a Teraflex or Lowmax conversion to their Dana 300?
What are the pros and cons for doing the swap and are there differences between the various manufacturer's kits?
What about the output shaft replacement?
OK I am putting a Dana 60 in the rear. I know the proper way to set the pinion angle would be to wait until the truck is finished, loaded and sitting at finished ride height. Then I would set the static pinion angle to where the pinion was a couple of degrees down from being parallel to the...
Scott Anderson's Tube Fenders Are Inspiring Me To Try And Make My Own. Anyone Have A Drawing Or Rough Sketch Of What Is Needed?
I Guess A Lot Of People Would Like To Do This Same Project
This is driving me nuts. I developed noise in my throw out bearing, but it only at idle, When you step on the clutch it goes away . The clutch and bearing are less than 500 miles old. The noise is a squeeking noise and as soon as you touch the clutch it stops
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.