• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

All wiring harnesses the same?

WyTex

Basic User
City
Jeffersonville
State
PA
Are all the CJ8 wiring harnesses the same? Would a base edition have the wiring for the clock and tach but it's just tied up in the dash? Thanks!
 
I just did a clock and tach install on my 81 Scrambler. If you can, get a factory clock that has the second hand. Aftremarket clocks only have the minute and hour hands. The clock will plug into the fuse panel at the "clock" marled locations, there are two of them (get the factory clock harness with the clock). The orange wire is for the light, Black is ground, and the Red and White wires plug into the fuse panel. Get the factory wire harness, it makes the install easy. The tach will plug into a harness that is next to the steering column. There should be a large red wire (about 10-12 ga.) with a white stripe, the tach plugs into this harness. You will need to de-mate the connector and connect the plug and socket from the tach into this demated connector (I say de-mate because I work in the aerospace industry). The factory tach is current driven, meaning, electrical current from the battery flows through the tach, through the harness and out the firewall to the ignition coil, then to the distributor. The tach measures the electrical current pulses caused by each cylinder firing and converts them to an RPM indication on the tach. If you have an HEI, DUI or other aftermarket modern electronic distributor the factory tach will not work. HEI's and DUI's are voltage driven, not current driven. I installed an HEI in my 81 Scrambler, so I bought my aftermarket (Crown) looking tach from Hesco (also works with the Mopar EFI kit), set the tach to the proper engine size 4-6-8 cyl. Hope this helps.
 
Yeah, that helps a lot actually. You mentioned to get the factory wiring harness. I'm assuming it means that you did not find the necessary clock and tach harness behind the dash in your base edition?

Thanks.
 
If you have an HEI, DUI or other aftermarket modern electronic distributor the factory tach will not work.

I have a DUI that I'm running on a 401 with a factory AMC CJ V8 tach. It works perfectly, and is accurate.

I also have an HEI that I'm running on a SBC 350 with a factory AMC CJ-7 I6 tach. It also still works perfectly, but is wrong since it's calibrated for the I6 instead of the V8.
 
How did you get the factory tach to work with your HEI?

On my orange CJ-7/carcass (it's giving up its life for my Scrambler project) that did NOT come with a factory tach/clock, I cut a hole for the tach, and then de-mated the red wire with a white tracer and inserted the tach wiring. The wiring is all factory.

On my black CJ-7 that did come with a factory tach/clock, the tach worked perfectly (if inaccurately) after installing the SBC 350. Again, the wiring is all factory.

I don't understand why an HEI wouldn't work?
 
I could be wrong (it' been awhile since I did mine) but I remember something about the tach wiring for a 4 cyl and a 6 cyl being different. And even though mines a 6, I was able to use the 4 cyl wire (which was also in the factory harness) to power an aftermarket tach.
 
I rechecked my tach wiring. I did use the 4 cyl. wire harness to power my aftermarket tach (kinda). I cut off the plug, Used the black wire for ground and the yellow wire for power. There's also a purple wire for the tach signal but it only goes to the connector on the firewall. To use it, you would have to finish the connection on the engine side to the coil. I plan to do that but for now I just ran a seperate wire all the way.

The point of all this is I do believe the wiring is present for most of the unused options.
 
Back
Top