- City
- Claflin
- State
- KS
I'm needing some direction with an issue I'm having on my 1979 Jeep Cherokee S 4 door. The Jeep has what appears to be a stock rebuilt 360 with the 2 barrel Motorcraft 2150 carburetor. The Jeep had sat for several years before I purchased it.
The issue I'm having is, right off idle when you hit the throttle hard, the Jeep seems to stumble for just a second or two then catches up with the throttle and revs up fine after that point. If I ease into the throttle there is no issue. It only occurred under moderate to hard acceleration.
When I was first getting the jeep running before the carburetor was rebuilt, I had several backfires through the carburetor due to a few vacuum leaks on some old lines. I wanted to replace the power valve after the backfires and that is what lead to the rebuild. I have checked the float and the fuel bowl level with the engine running and they are spot on. When I replaced the vacuum lines I eliminated most of the CTOs, Air pump, and other various emissions equipment, except for the EGR. The distributor advance is now run off of manifold vacuum (I have tried ported vacuum too and that did not chance the off idle stumble).
Distributor is currently sent to 8 degrees BTDC. I have tried advancing and retarding the timing; I even timed it with a vacuum gauge, none of which got ride of the dead spot under hard throttle. I did check the distributor advance and and it is working and will hold vacuum.
My best idle mixture screw adjustments when tuning with a vacuum gauge came in right at 1-1/2 turns out (will double check this) for each at 18 in Hg (one side note to this is with the mixture screws in so far for the best vacuum reading the jeep would not start after a day without dumping gas down the carburetor, I backed the screws out to 2-1/2 turns and this starting problem went away). I have since tried several different idle mixture screw settings and nothing has eliminated the hesitation off idle.
The accelerator pump has been replaced twice, thinking maybe the first one was bad; no luck. I have also tried moving the accelerator pump rod to the other positions, still nothing.
The only other issue I can think of is the throttle shaft on the driver's side appears to have a very small vacuum leak around it. If I spray carburetor cleaner on it the RPMs will vary slightly. Don't think this could be enough of an issue to cause my problem?
I'm about to pull the Motorcraft off and build a junkyard TBI from parts I gathered from a salvage yard while I lived in Houston. I've never had so much trouble with a carburetor in my life!
Short summary: Stumble off idle under hard acceleration.
-rebuilt carb
-manifold distributor advance set at 8 degrees BTDC
-idle mixture screws set to the rich side at 2-1/2 turns out.
-replaced power valve twice
-replaced accelerator pump twice.
-very slight vacuum leak on driver side of throttle shaft.
Anyone have any input on what to try next? I've spent the last several nights trying to get this working correctly but no matter what combination of settings/adjustments I try, the off idle stumble is still there under moderate/hard acceleration. Will post pictures of the Jeep as soon as my frustration level comes down!
Sent via signal flare
The issue I'm having is, right off idle when you hit the throttle hard, the Jeep seems to stumble for just a second or two then catches up with the throttle and revs up fine after that point. If I ease into the throttle there is no issue. It only occurred under moderate to hard acceleration.
When I was first getting the jeep running before the carburetor was rebuilt, I had several backfires through the carburetor due to a few vacuum leaks on some old lines. I wanted to replace the power valve after the backfires and that is what lead to the rebuild. I have checked the float and the fuel bowl level with the engine running and they are spot on. When I replaced the vacuum lines I eliminated most of the CTOs, Air pump, and other various emissions equipment, except for the EGR. The distributor advance is now run off of manifold vacuum (I have tried ported vacuum too and that did not chance the off idle stumble).
Distributor is currently sent to 8 degrees BTDC. I have tried advancing and retarding the timing; I even timed it with a vacuum gauge, none of which got ride of the dead spot under hard throttle. I did check the distributor advance and and it is working and will hold vacuum.
My best idle mixture screw adjustments when tuning with a vacuum gauge came in right at 1-1/2 turns out (will double check this) for each at 18 in Hg (one side note to this is with the mixture screws in so far for the best vacuum reading the jeep would not start after a day without dumping gas down the carburetor, I backed the screws out to 2-1/2 turns and this starting problem went away). I have since tried several different idle mixture screw settings and nothing has eliminated the hesitation off idle.
The accelerator pump has been replaced twice, thinking maybe the first one was bad; no luck. I have also tried moving the accelerator pump rod to the other positions, still nothing.
The only other issue I can think of is the throttle shaft on the driver's side appears to have a very small vacuum leak around it. If I spray carburetor cleaner on it the RPMs will vary slightly. Don't think this could be enough of an issue to cause my problem?
I'm about to pull the Motorcraft off and build a junkyard TBI from parts I gathered from a salvage yard while I lived in Houston. I've never had so much trouble with a carburetor in my life!
Short summary: Stumble off idle under hard acceleration.
-rebuilt carb
-manifold distributor advance set at 8 degrees BTDC
-idle mixture screws set to the rich side at 2-1/2 turns out.
-replaced power valve twice
-replaced accelerator pump twice.
-very slight vacuum leak on driver side of throttle shaft.
Anyone have any input on what to try next? I've spent the last several nights trying to get this working correctly but no matter what combination of settings/adjustments I try, the off idle stumble is still there under moderate/hard acceleration. Will post pictures of the Jeep as soon as my frustration level comes down!
Sent via signal flare
