• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Axle Rebuild Question

hefavitzen

Scrambler Junkie
BENEFACTOR
Gold Member
Lifetime Member
City
Rock Hill
State
SC
Hey guys, I just bought a set of wide-track axles for my Scrambler and I have a few questions for you all. These are a Dana 30 and an AMC 20 (AMC 20 has 1 piece axles and a locker) and came out of an 83' CJ7 just about 5 weeks ago. But, other than that I do not know their history.

The axles appear to be operational with not a lot of sign of a lot of leaking.

1) Since they are already in the back of my truck, should I take them to have them rebuilt somewhere?
2) Should I just rebuild them myself? I have hand tools and no press and while I do have a service manual and can follow directions, I've never done more than change brakes on an axle.
3) Should I just clean them, paint them, install them and if they break then rebuild them?

Just not sure where to go from here. My inclination is to have them rebuilt so that I can feel more confident that I'll get another 30 years out of them, but I hear that will cost me around $3000 for the set or something like that.

Any advice or your experiences would be appreciated. I went with factory wide tracks just for my own ease of implementation and familiarity. Plus, they were cheap. :p

Thanks! Jeff
 
$3000 to have them rebuilt is ridiculous unless you add lockers of some kind, especially if you do not change gears.

Sent from my SM-J320P
 
Do it yourself. It may be new for you, but it's not difficult, and you'll know exactly what's going on in there from now on!

It's nice that the axles are already out in the open to work on.

To me, removing and re-installing axles is the worst part! Once the axle is on your bench (or sawhorses, in my case), the rest is pretty easy... until you get to the crush sleeve on the AMC20 pinion.... ;)

Seriously, it's a good project to do yourself, if you have time! :thumbsup:
 
Do I just buy a kit like this? Or do you guys recommend not replacing some things? I'm of the mind that since it is all apart, why not just replace the wearable parts like bearings, u-joints and ball joints. Am I wrong?

Dana 30 Rebuild Kit - https://www.ringpinion.com/b2c/ProductDetails.aspx?ProdID=3041&Source=DiffWizard&ShowAA=true

AMC 20 Rebuild Kit - I'll have to break open the rear to figure out 1) who made the 1 piece axles 2) what type of locker is in there. before i order a kit.

Ideas?
 
If the axles have an m/e on the end, between the studs, they are moser axles (unless they did away with that my old moser were bought 20 years ago. Chances are the rear with 1 pc axles and a locker will not need bearings and stuff replaced if the oil looks clean and uncontaminated.


Sent from my SM-J320P
 
The bearings wear more than anything else in the axle.

I always replace the bearings anytime I disassemble anything... but I own a bearing store, so that's easy for me to say. ;)

If you, or any other member of this forum needs bearings (for personal projects only), I'll send them to you at my cost + shipping.

I carry Timken and SKF, so you'll be getting the good stuff.

Be careful ordering kits... most kits use Chinese bearings to keep the cost down, and Chinese steel just doesn't hold up very well.

You need to research the part numbers though, I'm an industrial distributor, not automotive.

Cheers! :cheers:
 
I just looked at your link to the rebuild kit, and it specifies Timken bearings, which is good. However, ask about the seals, as well.

I got a Dana 300 rebuild kit from Novak a few years ago, without the bearings, as I was providing my own.

When I installed in in my CJ7, the kit-supplied shift-rod seals leaked like crazy! I replaced the seals with SKF (CR) seals off my shelf, and the leaks stopped.

Kits are convenient, but it's worth the extra time and expense to source your parts individually, if possible.

Ideally, you'll only be doing this once... so it's worth doing it right the first time!
 
Yep, big ole " M E" stamped onto the end. I'll just pull the cover and see what is what...like what the gearing is.
 
That is good advice! Thanks!

And thank you for the offer!
 
So I am about done with my axle rebuild and have a few questions:

1) How hard is it to actually get the new axles under the Jeep?
2) Do I attach the leaf springs outside of the Jeep and then, with tires attached, just roll the set up under the Jeep and bolt it all in place?


Also, truth be told, I've only cleaned up the axles and inspected them. So, a few more questions:
1) the rear end seems to be in good shape with no leaking. Should I pull the axles and regrease everything or just clean it, refill fluid, brake job and install?
2) the front was pretty rusty, appearing to have spent some time sitting in a puddle. At least one ball joint appears to have given up it's grease all over the knuckle. But, for all the crusty, it all seems to move freely.
So my question would be - should I go ahead and replace all the ball joints and ujoints in the axles and the bearings just for good measure? Seems like I should but curious what you guys usually do.

Thanks!!! Jeff
 
^^^^^^^^

And as for reinsatll, all I do is attach the main eye end of the leafs to the frame. Jack up the frame as high as needed to get the axle in and attach the shackle end of the leaf without stressing the leaf at all. Attach axle to leafs with u bolts. Lower Jeep. Retighten all bolts.

A week later, retighten all bolts again
 
The bearings wear more than anything else in the axle.

I always replace the bearings anytime I disassemble anything... but I own a bearing store, so that's easy for me to say. ;)

If you, or any other member of this forum needs bearings (for personal projects only), I'll send them to you at my cost + shipping.

I carry Timken and SKF, so you'll be getting the good stuff.

Be careful ordering kits... most kits use Chinese bearings to keep the cost down, and Chinese steel just doesn't hold up very well.

You need to research the part numbers though, I'm an industrial distributor, not automotive.

Cheers! :cheers:

Tagging this for future reference as I'm going to be doing bearings at some point and will want to bend your ear. I've heard Timken is being made all over the place now so simply buying Timken isn't necessarily foolproof anymore. The seal thing is interesting too, as I wouldn't have thought twice about seals being better or worse.

Interestingly enough, in rebuilding an ATV engine last week, I noticed a Honda OEM seal that was made in China. I muttered about it and the wife said "Did you think it would be made in the US?" I said, no, I thought it would be made in Japan!
 
Tagging this for future reference as I'm going to be doing bearings at some point and will want to bend your ear. I've heard Timken is being made all over the place now so simply buying Timken isn't necessarily foolproof anymore. The seal thing is interesting too, as I wouldn't have thought twice about seals being better or worse.

Interestingly enough, in rebuilding an ATV engine last week, I noticed a Honda OEM seal that was made in China. I muttered about it and the wife said "Did you think it would be made in the US?" I said, no, I thought it would be made in Japan!

I have bought, but have not installed, Moog ball joints and u-joints for the front Dana 30 from Advanced Auto. They have reordered the u-joints three times until I just took the best looking one of what they had. Reason being, all the ball joints and one of the two u-joints were all made in the USA. The rest of the u-joints they had and kept getting were all made in Mexico. We'll see what happens, but it is frustrating.
 
The bearings wear more than anything else in the axle.

I always replace the bearings anytime I disassemble anything... but I own a bearing store, so that's easy for me to say. ;)

If you, or any other member of this forum needs bearings (for personal projects only), I'll send them to you at my cost + shipping.

I carry Timken and SKF, so you'll be getting the good stuff.

Be careful ordering kits... most kits use Chinese bearings to keep the cost down, and Chinese steel just doesn't hold up very well.

You need to research the part numbers though, I'm an industrial distributor, not automotive.

Cheers! :cheers:

So, I do need bearings and seals for the Dana 30 and the AMC20. I cannot figure out how to control the manufacture location of parts upon ordering, just having to take what is given. Do you have advice for doing that or do you have US made parts you can sell?

Let me know! Jeff
 
So, I do need bearings and seals for the Dana 30 and the AMC20. I cannot figure out how to control the manufacture location of parts upon ordering, just having to take what is given. Do you have advice for doing that or do you have US made parts you can sell?

Let me know! Jeff

Let me see what I have on the shelf. I have a feeling the Timkens will be US made, but I'm not sure about the SKF (CR) seals. I also carry SKF u-joints, but I think they are made in Mexico.

I'll get back to you later today!
 
Back
Top