• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Clutch linkage issues

ScramblerTN

Basic User
City
Lenoir city
State
Tn
Finishing up the last bit of final touches on the scrambler and I'm having a hard time with the clutch. There was a new clutch and throwout bearing installed before engine was dropped back in. I've got the linkage backed all the way out and still cannot get it into gear while running. I can get it into reverse, 3rd and 4th but not 1st,2nd or 5th. ( gears grind a little going in reverse). I've looked at diagrams and pictures online and am 99% sure I've got the linkage bolted up correctly. Any thoughts on what will cause this?


 
I should add that I did reuse the factory linkage...replaced bushing in bell crank but all linkage is original to jeep


 
The linkage is pretty straight forward down there. I have recently spent some time looking at and replacing my linkage. Do you have any pics?
 
I don't have any pictures but I can take some. As you said..it's very simple. I'm about certain the linkage is put together correct. I started out with the linkage about half way ( the jeep wanted to take off when it was cranked in 1st gear with clutch to floor). Kept backing out linkage from there.


 
Does it go into those gears with the engine off?

Did the trans work ok before the engine swap?


 
Is the shift cane contacting the edge of the hole in the tunnel/access cover? If so, you may need to loosen the skid plate and/or transmission/transfer case mount and push it all to the right a little.
 
Is the shift cane contacting the edge of the hole in the tunnel/access cover? If so, you may need to loosen the skid plate and/or transmission/transfer case mount and push it all to the right a little.

By shift cane are you referring to the shift fork? Maybe hitting side of bellhouse? That could be a possibility


 
e3aecc2650f68aaffdd193b43d7f2e67.jpg
a2a7a2092113ba83e8616179252cd343.jpg
416e356dad2df2b045d4e992f389782a.jpg

Ok here's a few pictures. It seems like the clutch fork isn't going in far enough even with no more adjustment. It's defiantly not hitting the bell housing. I let looks correct to me but could the bell crank be turned around backward?


 
Temporarily put a spacer between the linkage and the clutch fork and see if it shifts ok like that (use a socket or something). If that temporarily solves the problem, then you'll know you need to fool with the linkage. If it doesn't solve the problem then maybe the problem is internal to the transmission.
 
Yours are angled a little different than mine. For some reason I can't upload pictures right now on the forum. PM me your cell number and I'll text you the pictures of my setup. I still have the original clutch and linkages on mine that have never been touched so it's a good reference.
 
Yours are angled a little different than mine. For some reason I can't upload pictures right now on the forum. PM me your cell number and I'll text you the pictures of my setup. I still have the original clutch and linkages on mine that have never been touched so it's a good reference.

Hey Ron. Tried to PM you but lt says over my PM limit....anyway my cell is 865-437-7547. Appreciate your help!


 
Wait, nevermind. They are the same. My eyes were playing tricks on me at first glance.
 
I just left you a message. I have a linkage that was only used for a couple of weeks if you need one. Feel free to call me if you need anything else. I have a bunch of near new 6 cyl stuff that I will be selling for cheap.
 
I just left you a message. I have a linkage that was only used for a couple of weeks if you need one. Feel free to call me if you need anything else. I have a bunch of near new 6 cyl stuff that I will be selling for cheap.

Hey Ron. Tried calling you back. The linkage is OEM and it worked great before the jeep was tore down so I doubt the linkage is the issue. I thought maybe I had put the linkage in wrong or somehow had it hooked up wrong. I'm hoping that it isn't internal but I'm running out of other possibilities


 
Its probably too late, but just in case. What is the distance the fork fingers are off of the throwout bearing surface?
Everyone want to talk about a certain amount of pedal play or travel. I don't understand this as the are many points of wear or gaps in the linkage pivots and bushings. Plus each Jeep has different amounts of wear.
Instead, go straight to the fork. While under the Jeep, push the adjuster rod forward away from the fork and hold it forward. With the other hand, move the fork back and feel when it touches the bearing. 1/8" off the bearing is good. That translates to about 1/4" movement on the adjuster end of the fork. The fork spring will keep it from riding on the bearing once its adjusted right.

I'm guessing you have too much gap off the throw out bearing and the travel of the system isnt enough to make up for it.
 
Back
Top