• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

CTO Ported Vac Switch

Big E

Basic User
City
HB
State
CA
California 1981 CJ8 Scrambler 258 rebuilt BBD 4 Manual- She’s just not running well, I started looking at the vacuum connections that the PO hooked up. I found that the EGR valve is leaking so I will be installing a new one this weekend. The EGR is plugged into the CTO ported vac switch (just below carb to the front) rather than test the CTO to make sure it was functioning properly I though well I will just replace it… BUT I’m questioning the CTO itself if it’s correct or not. What I have is a 5 port but when I search various part sites they show the 2 port for my scrambler :confused:


Digging deeper I reference the Jeeps Parts Manual 81 thru 86 it reference’s this part as a “Duel Functioning CTO” and calls out part number J323-8932 that C/R to Napa PN CRB 229048 (5 Port) that’s what mine looks like... But Napa’s web site say’s that part won’t fit my vehicle and directs me to the 2 port model CRB 21084 for my vehicle.

BTW- This is the only ported vac switch I have on my jeep. But the manual also shows an “EGR, CTO Switch” PN J323 8932 (another 5 port) but the part is illustrated as a 2 port in the manual? And a switch to spark CTO part J535 8881 C/R Napa part CRB 21000 3 port but I don’ have that one either.
Looking for comments on 5 or 2 port CTO and how they should be hook-up, I’m not sure but I believe the vacuum source should be ported and not from manifold vac. Also not sure where the source vac is plugged into the CTO (which port)?
 
Somewhere on jeep forum there's a few diagrams. It's been a while since I've checked, but you might try over there? Lots of knowledgeable engine people there.
 
You might check out this site http://home.sprynet.com/~dale02/. I have found it helpful in understanding the emissions and what everything does. If you suspect a vacuum leak related to the CTO or anything connected to it, temporarily unhook it and cap the port. The CTO is not necessary for the engine to run correctly.
 
Last edited:
Have you seen this for the '81?
vac.JPG

Here is a clearer one for an '82:

vac2.JPG

HTH :thumbsup:
 
Recalled I had this in my archives. Don't recall where it came from, but likely from this site or a referral from here. Maybe it helps.

Dual CTO Valve - The Coolant Temp Override valve is a switch for both the EGR and the Evap charcoal cannister. At the proper time, the CTO permits ported vac from the carb to pass through the CTO valve. Of the 3 ports facing closest to the radiator, the port at the bottom of the CTO valve (near the threads into the engine block ) should be closed off / sealed / blocked. The middle port hose feeds ported vac "signal" to the evap cannister. This permits the opening of the evap cann "purge main port", allowing vacuum from the carb (manifold vacuum). The third outer CTO port is teed into the CTO port which is on opposite side of CTO (2 port side) and closest to engine block. Together, the conjoined hoses lead back to the air cleaner thermo vacuum switch TVS. Not until both engine coolant temp and TVS have hit their respective critical temps will the ported vacuum source (originating from carb half way up the side facing the valve cover) hooked into the outer CTO port (on the two port side) be permitted to flow through the CTO and TVS. When this occurs, ported vac is allowed to turn on the evap cannister "Signal valve". Also, ported vac is permitted to flow to the air cleaner's TVS, through the TVS, and then on toward the EGR.
 
FLCJ8
Thank you for the Diagrams.....
Xatu40
Your description is clear and easy to follow but it differs with much of how the above schematics details. I get that the schismatic above Can you please help me understand what you are describing (I never heard of plunging the first port but that certainly doesn’t man anything) where do you hook the Dist Advance up in your application? Can you comment on the above 1981 schematic?

BTW I need to replace my original Air diversion valve (Gulp) (3223643) the only part I can find it says it for an automatic (Carter 3230816 https://www.ebay.com/itm/Carter-323...-Valve-Jeep-CJ5-CJ7-258-4-2L-L6-/231183766361 .can I use this in my manual trans if not does anyone have a suggestion.
 
Unfortunately, I did not write that description and did not save the link for where I found it. I pulled my schematic, which is for an 83 and it appears to match except for "hooked into the outer CTO port (on the two port side)", which I believe should be inner CTO port, based on the diagram below. I'm guessing the "plugged" may have come in to play with the 83 and the addition of the computer. Sorry, my knowledge is pretty limited in this area. I have been tracing the mess under my hood and the color code depicts what I have figured out so far.
 

Attachments

  • Vaccum Lines 20180408.jpg
    Vaccum Lines 20180408.jpg
    66.8 KB · Views: 56
Back
Top