• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Driveshaft lengths

flashover604

Scrambler Junkie
Lifetime Member
City
Lancaster
State
Oh
Hi all. I've currently got a 258-T4 combination in my Scrambler. I've come across a decent deal for a 258 with a 4.0L head conversion and a T176 transmission. My 258 has a crack in the block near the water pump. My T4 leaks like a Washington politician and pops out of third gear. I'd like to swap the engines and transmissions.

Two questions:

First, the T176 is not attached according to the owner. Any tips on evaluating it prior to buying it?

Second, driveshafts. According to my Google-fu, the 258-T4 should have a 31.75" front shaft and 30.6" rear and the T176 should have a 29.50" front and 32.88" rear. Do those measurements sound correct? I assume that I'll need two new shafts, correct?

Thanks in advance.

Zach


 
Don't know for sure on the sizes. I assume those measurements are u-joint center to u-joint center while slip joint is compressed and not mid-extension? BTW- A spring or shackle lift will make the stock shaft lengths somewhat irrelevant (don't know if you are still using a stock suspension or not). Have you measured your current shafts for comparison? Ideally you want to measure the distance between yokes and use shafts that are equal to that length at mid extension.

It's pretty easy (and cost effective) to shorten an existing shaft rather than to buy a new one. As long as the ends are in good shape, they can be reused after cutting a section of the shaft out.
 
I sold a T5 to a guy two weeks ago to replace his T4
A week later he calls me and tells me he screwed up, he has a T176
His 176 made a growling noise so he traded me for a nice tire carrier and all brackets
Then I traded him even for the Bellhousing's, front and rear driveshaft, tunnel cover, and the Dana 300 stick shift
Also had to trade reverse switch connector


 
You know what, I'm glad that you mentioned the lift. I've got a four inch lift ready to be swapped in that could've gotten expensive...


 
The t176 is an easy trans to pop the top cover off, simple tools , and no disassembly or extra time like to look in a T4 T5. You can't be sure totally lookin inside a T176 about snychros but you can get a very good idea about the gears and a look inside the case. Rotate around and look for chipped teeth etc. if drained , look even further what's on bottom and any thing not normal. [emoji1303]
 
I bought them. The 4.2 looks to be a Capital City Rebuilders engine. No cracks in the clean block. Oil looked clean and oil cap didn't have any sludge, but didn't look like it'd been wiped off. The aftermarket header has a small crack where it y's off from 2 to 1. It still has the flywheel . It had a Pro Comp hei style distributor. I'm a little concerned about the distributor gear being hardened, but I have the new cam in the old 4.2 if that's the case and I plan on swapping in the DUI distributor when I do the engine swap.

The transmission looks good under the top cover. No chips or gnarled teeth that I could see. The input shaft has a bit of movement side to side. I'm assuming that there should be none and I'll need to rebuild it.

The transfer case is still attached and I'm assuming it's the D300 due to the aluminum lever mount and aluminum output housings. This was a bonus. He'd told me that he had a spare d20 that he'd throw in. I'll take the d300! It also still has a very nice front driveshaft. The front joint is missing the two axle side caps and bearings so I plan on replacing the ujoint if I re-use the shaft.

I also got a clutch, clutch fork, two bellhousings (one that he thinks is for a T18) and an extra flywheel.

For $325.


 
Back
Top