• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Flashover604's incomplete build and non-restoration

Test fit. The door was open a little so it looks uneven. It's not. These things are NICE! And heavy. 60lbs apiece. I also noticed that I need longer bolts due to the fiberglas being doubled up and thicker then the the original body. Looking forward to getting these painted and bolted up. http://
 
Very nice, now take em and get them powdercoated. That way they're sealed all the way around and wont rust and the finish will be super tough.
 
Looking good. Those rockers are mighty tasty !!

Aren't they? Heavy rascals. They're back burnered for now. I need to get the frame done then get the body back down and bolted so I can drive the jeep again, THEN get the rockers on. There are going to be a couple of snags. First, the rockers are notched to slide past the original body bushings. My 4WD hardware Fiberglas tub has the two body bushings under the door closer together that stock, so I'll need to make a couple new notches to fit the new locations. Also, the Fiberglas is 1 3/4" thick where the middle five bolts go instead of the single thickness of steel, so the 1" long stainless cap screws need to be more like 2.5" long. Those are $2.50 apiece... I'm going to run a 2" wide by 34" long by 3/16" thick strip inside the tub to spread the stress of the five bolts. I'm not sure if I should sleeve the bolts or not. Hopefully I'll get most of the frame finished this weekend and have my welder friend come in and do his finish magic...
 
Took a few minutes and threw the JB Fabrication twin stick kit on. Easy peasy. Twenty minutes start to finish. Pull the old stuff off, clean up what I could on the transfer case, follow the five steps total in the instructions, tada! Two levers. I'm looking forward to rear low and front low independently. http://
 
Last edited:
So, I rescued a couple Runcks today. I found the rear on Craigslist and made an offer. The owner countered with no drop in price, but he'd throw in the matching front bumper. Six am this morning I started on a 250 mile round trip. Met the guy, paid the guy. No haggling, as I thought it was a good price, and he knew I wasn't going to waste five hours and $35 in fuel just to go home over $10... Remember how my Scrambler is still in frame resto mode? Yeah... That leaves the Volkswagen. Just for reference you can fit a front Runck bumper and rear Runck bumper/tire carrier combo in a 2000 Jetta.

I got home and started cutting the remnants of the front bumper mounting bracket/weld globs/big a$$ chunk-o-steel that the PO left after cutting it off the old jeep. I went through a cut-off wheel before shutting down for the night. They'll take some work but should look much better than the slightly twisted front stainless racing bumper and brush guard on there now. (on a side note, I have a slightly twisted front bumper, stainless with holes and a stainless brush guard for sale) I needed a rear bumper anyway and like the Runck stuff for the old-school-coolness of them. One more thing to clean up, prep and paint...
 
That rear looks a lot like mine. Except you have the locking thing. I had to weld on a latch. Great score. It should look great once you clean them up.


Dain
 
Transmission question. I have a couple incomplete pictures of my transmission. I THINK it's an SR4, but I want to make sure. I'm going to change all of the fluids and want to figure out how I need to drain it. I've heard that there is not a drain plug on the sr4? Here are the pictures I've got. Sorry, they're not that but they're all I have right now since the jeep is an hour plus away... Thanks in advance.
ImageUploadedByTapatalk1379598891.595764.jpg
ImageUploadedByTapatalk1379598970.847331.jpg
 
I found this thread about the sr4.
https://www.cj-8.com/forum/showthread.php?t=24370
It appears that mine IS an SR4. Now I have two questions. First, after I remove the lower drivers side bolt and drain the fluid, how do I refill it? Just pop the top cover and dump the correct amount in? Is that bolt the lowest part of the transmission? It looks high to me, but I can't see the internals. Ok, three questions... What is the two pronged sensor/plug in the second picture? It had a yellow and red wire coming out of it. Mine had nothing plugged into it.
 
You don't have a sr4, you have a either a T4 or T5. fill bolt is on the pass side of the transmission and the drain bolt is on the bottom. pressure switch in the second picture activated the reverse lights.
 
Man, your project is coming along good! I had the same issues with mine except I had a Flintstone steel body. I ended up making new frame rails from the first body mounts to the rear bumper (25ish hours) using 2x3 and 2x4 box. Surprisingly convenient dimensions once it was completed. I should be back on the road within a month (has to be, I have a bet going) and will post a build thread then.
 
Hoddy folks... Well, after a thirteen hour day Wednesday and a dozen yesterday give or take, I have made a lot of progress. As of 2am this morning my Scrambler exited my buddy Jared's shop under its own power. That means that (A) I got enough wiring put back in its original place that the electrons are heading where there supposed to and that the fuel is meeting them in the correct place, at the correct time, and under the correct conditions. (B) the Frame now resembles an actual part of the structural makeup of the vehicle, and (C) I'm tired and sore.

So, here's my breakdown of work completed.

The frame. I pulled the body off of the frame. (by far the most dramatic work I've ever done on a vehicle. Seeing my single jeep in two very large pieces was damn cool. I took a wire wheel to the frame and discovered much more rot than I expected. Bad stuff. (picture yourself buying a nice fixer-upper house. It looks good but has a couple missing shingles on the roof. You get up to replace them and find that termites have eaten the whole other side of the roof. That was me. It sucked. (thanks to ChiefWaho, those frame plates ROCK man.) I couldn't tell you how many pieces of steel were welded in to replace missing or tin-foil thick spots in the frame. She's stout now though! The rear frame sections from the rear crossmember forward were cut off and relaxed with 2"x2" 1/4" thick steel. The rear two crossmembers were replaced with ChiefWaho pieces. All that's left now is to weld on the rear body mount brackets and FluidFilm the frame.

Transfer case was drained, refilled with Lucas Oil Gear oil. Twin Stick setup was installed.

Transmission was drained, refilled with Amsoil MTF and Lucas Oil Transmission stuff.

Emergency Brake cables replaced.

Tune-Up

Fuel Tank cleaned out, new sending unit installed. I'm not gonna lie, seeing the gauge respond when fuel was added MAY be one of the happiest moments of my Jeep owning experience...

Electric Fuel Pump relocated to the rear near the tank.


Now, here are my immediate problems...
I have a small wire up near the voltage regulator that I cannot figure out where to reconnect. It has a single aluminum conductor, not stranded copper like every other wire. Any help would be greatly appreciated.

My heater and windshield wipers don't work.

Hopefully I'll get it home this week!

ImageUploadedByTapatalk1382882414.302756.jpg
 
Thanks Dain! It'll hopefully be back home this week. I sure hope I can get the heater figured out though, it still just has the bikini top on it! I started working in it in August and never figured it'd take this long to finish!
 
Well, I took it for a ten minute "let's see if anything falls off, burns up, destroys itself, quit working, or just generally leaves me on the side of the road" shakedown cruise. Shifts fine, drives fine, idles fine, stops fine... Works for me. I got the heater working (dirty spade on heater) and the wipers (power lead got pulled off). Now I just need to get the shifter boots re-installed to stop that draft coming up through the floor. The rear brakes need adjusted so that the e-brakes work. I hope to have it home Wednesday. It's supposed to be in the fifties so at least it will be a tolerable 45 mile drive with the top off. From there I hope to get the half hardtop back on, the runck rear bumper on, and some more connectors replaced.

She's coming home...
 
ImageUploadedByTapatalk1383161235.956572.jpg

Back home. 45 miles, 0 problems, other than my gas gauge. It works now, so I can actually see the level drop. It's a Nordskag digital unit that reads in percentage, so a full tank reads 99 so I figure with a twenty gallon tank each percentage point is .2 gallons.
 
Nice project you got there. I hope to find me a project '8 here soon. I get through Lancaster every so often for work! How do you like the fiberglass tub so far? I wonder if you could lengthen a CJ7 to an '8. I also like the LJ's.
 
I think I like the Fiberglas. No rust to worry about here in Salt-Ville. The grounds aren't that big of a deal. Run a good buss bar up under the dash, wire it to a good solid frame or engine ground and your good. I've had more trouble finding AND KEEPING a good ground on a rusty steel jeep than I've had on this one. I'm just going to have to reinforce some stuff to suit me, like rear seat mounts and seatbelts, but all in all I like it so far. As for lengthening a 7... I think it's certainly possible, but I think by the time you find a good donor 7, with a good frame, then a second good body and frame to graft in, you be way farther ahead keeping your eyes peeled for a good 8. They're out there. It took probably four months or so for this one to drop in my lap. I'm SO glad I waited and didn't buy the first second third or fourth ones I looked at. (Thanks Big Walton for talking some sense into me) I was overlooking major flaws because I wanted a Scrambler BAD. Impulse buying is for the grocery store, not Scrambler-land. I've got the gut to prove it...
 
Back
Top