• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Half Hard Top Bulkhead Seal

wannascram

Scrambler Rookie
Lifetime Member
City
Dripping Springs
State
TX
Since buying my 82 I have not ventured out with the top off. My concern is that if I remove the hard top and bulkhead I'm going to break the "clearly DIY silicone seal" that resists "most" moisture. Wondering if there ever were, or still are a bulkhead seal (body tub to bulkhead) that can be purchased. Any thoughts from those of you that consistently go back and forth between top on and top off?


Sent from my iPad
 
I'm interested in this, too.

I don't think my bulkhead has ever been removed... but it leaks a bit when it rains. I've been debating whether to remove it, clean it, and re-seal it with seam sealer, or just goop on some seam sealer from the outside.

I live in a pretty dry climate, and I also have covered parking during rainy weather. I'm leaning toward leaving the bulkhead in place, and applying seam sealer from the outside....
 
I'm not opposed to doing the old silicone sealer trick again, but it clearly looks DIY already. I know my 8 has been painted, so it's been off at least once. Does the half hard and bulkhead come off as one unit or are they separate?



Sent from my iPad
 
I'm not opposed to doing the old silicone sealer trick again, but it clearly looks DIY already. I know my 8 has been painted, so it's been off at least once.

I know it probably goes without saying, but if you use silicone caulk, make sure it is 'neutral cure' and not 'acetoxy cure'. The acetoxy cure uses acetic acid for curing (the vinegar smell) and will cause corrosion.

Does the half hard and bulkhead come off as one unit or are they separate?

The half hard top and bulkhead are separate units.
The top detaches from the windshield frame, body side panel, and the bulkhead.
 
Thanks for the heads up FLCJ8! Great to know. I honestly haven't spent a ton of time looking at the top as much as I'm enjoying looking out the front windshield... :-). If that is in fact the case then I may just try and go with top only removal instead of top and bulkhead.


Sent from my iPad
 
Im in Wisconsin and only drive the Scrambler in the summer, mainly to keep the salt from making it a rust bucket... I have the bulkhead in place because it keeps whats in the tub in the tub instead of making its way into the passenger compartment.
 
Im in Wisconsin and only drive the Scrambler in the summer, mainly to keep the salt from making it a rust bucket... I have the bulkhead in place because it keeps whats in the tub in the tub instead of making its way into the passenger compartment.

Makes sense. I'll give it a shot.
 
There's no reason to remove the bulkhead if you just want to go topless. Though I have not yet gone topless since I re-bought the Scrambler, I'm sure I removed the top at least 100 times between 1982 and 1996. I had leaks at the bottom of the bulkhead when new, but applied some silicone caulk and it has not leaked since. I removed the top so many times that I had to tap out a couple of the holes in the rear of the top to the next larger bolt size. So when you re-install the top, do not over-tighten any of the fasteners. Been there, done that.

Perhaps my favorite aspect of the Scrambler is that one person can easily remove and re-install the top...and the top fits like a glove in the bed if necessary...though I would most often leave it at home. To remove it, I would just put the passenger seat forward, stand in that spot hunched over, then stand up (with the top resting on my shoulders and upper back) just enough to lift the top clear and carefully step out of the vehicle. It's a bit of a balancing act.

It's almost topless weather now. I can't wait. The guy who owned my Scrambler for the past 20 years never removed the top. He returned the bikini top and blue soft half doors to me in mint condition. I don't think you can buy blue soft doors anymore.
 
Last edited:
I believe a rubber seal is available to go between the top and bulkhead, I'm not sure who has them, likely crown or Omix or even Collins brothers. I need a thick gasket there to raise the rear of the cab a bit (not sure exactly how much yet) so the soft uppers on hard half doors will fit inside the "rain gutter" instead of mating against parts of the gutter. Anyone know what material to use or where to find something like that?
 
Trust, are you sure you have the uppers pushed completely into the steel lower door? Are they TJ uppers? Can you lower the rear pin to bring the rounded section down (together with adjusting the metal door's hinges)? Never heard of a spacer for the bulkhead. On my cj7 I have the bulkhead, half top and full steel doors (fiberglass body) and the half hard top fit pretty good.
 
And my TJ uppers on YJ half doors have no problem fitting under the rain gutter, and I have no seal between the bulkhead and the tub. My rubbing has been more along the back edge. But I fixed that by scooting the bulkhead back a smidge.
 
Thanks guys
Jammer, they are down as far as they want to go, the bend in the pin is maybe 1/2 to 3/4 inch above the top of the door, the bottom of the upper fits tight along the bend in the door skin. I suppose the pins could be slightly off the bore of the mounting holes but both sides are aligned the same but I'll give that a look manana. I didnt find any bottom to the mounting holes either. More tweeking maybe. Thanks

Hmm Thanks Dain, I guess its just mine. I wonder, mine is an early 82 top, besides the seatbelt holes, which mine does not have, are there other differences in the tops beyond the typical MFG variances?
 
I don't know of any other differences, but there are experts here that may know better.

Where does the bottom edge of the upper rest on the YJ half door? That may tell you if it is sitting too high. If I remember correctly, my uppers go to the crease in the door (assuming you have the rail removed from your door as it is not needed wth the TJ upper).

Here is the best pic I could find

28faec89f60be36e84c060bb68511588-1.jpg


Here is another more recent one that shows the fit at the top.

f38d42f0078f5f19a867a4e67ec902ed-1.jpg
 
Thanks again Dain, my passenger side fits as your does along the bottom, tight against the crease. it does not fit under the rain gutter. The driver side is about 3/8" above the crease but is tight to the door, I'll see if the bottom can be massaged some to allow the top to slide more fully into the door. Id go with more rake to the WS to move the top back a skosh and see if that helps. I sorta hate to though as the fronts make a decent seal, for a soft top

always something to work on or fix or massage....
 
Back
Top