• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Help! Weber carb 2nd stage flat spot..

Dave The Sparky

Rebuilding my CJ8 very,very slowly...
City
Halifax
State
UK
Anyone any good with these carbs?, been playing in the yard with my Scrambler and found it does not like being floored at all.
( I knew there was a reason why i prefer diesels :) )

The 32/36 Carb installed is new and was bought and shipped over from the US from 4wd hardware.
Engine is timed to 8 deg, she starts, runs and idles like a "good en", the problem only occurs when i press the pedal and the second stage kicks in on the carb and its like i have pressed a kill switch. The engine coughs,sometimes backfires and then basically feels like its trying to cutout.
As soon as i let off the pedal, all becomes good again.

The mechanical and vacuum advance are all to spec, the only possible thing that i can think that may be amiss is the gas which will be 10-12 months old now so wont be in the best of condition, but that would surely affect the rest of the carbs operation?

Any suggestions? Does it sound like there is too much fuel going in on that 2nd stage or not enough? if so does that mean re-jetting the 2nd stage??

Any advice gratefully received!!
 
It's been a while since I've had a carb, but it sounds like either too much gas or not enough oxygen. It explains the backfire - you've got unburnt fuel that gets through to the exhaust where it's hot enough to pop.

Rejetting? Let's see what everyone else has to say, but that's what I would consider your next step.
 
The 32/36 Carb installed is new and was bought and shipped over from the US from 4wd hardware.
Engine is timed to 8 deg, she starts, runs and idles like a "good en", the problem only occurs when i press the pedal and the second stage kicks in on the carb and its like i have pressed a kill switch. The engine coughs,sometimes backfires and then basically feels like its trying to cutout.
As soon as i let off the pedal, all becomes good again.

The mechanical and vacuum advance are all to spec, the only possible thing that i can think that may be amiss is the gas which will be 10-12 months old now so wont be in the best of condition, but that would surely affect the rest of the carbs operation?

Any suggestions? Does it sound like there is too much fuel going in on that 2nd stage or not enough? if so does that mean re-jetting the 2nd stage??

Any advice gratefully received!!

I have heard they are susceptible to problems with fuel pressure, and also heard they aren't. :shrug:

Here is a very recent post:

weber.JPG

Might be something to look into.
 
Is it backfiring out of carb? If so, and you know your timing is right and it doesn't smell like a rich fuel mixture, I would be looking at float level maybe being too low.
 
Well i had the Jets cleaned out today, so if its not raining over the weekend i will give it another go, hopefully was just gunk in the secondary's jet but i am not holding my breath!
 
I would be sure all that old fuel is gone. I also believe in a gas additive called Sea Foam. This stuff usually cleans out my fuel systems in with the first tank full. I have the same Weber and rejetted it 5 or six times. They are a real PITA to tune. My biggest problem was my fuel return line was restricted which resulted in to much fuel pressure. Thes carbs must be between 3 and 5 lbs pressure to work. I would never buy another one.

P.S. The Weber is like no other carb I ever tuned. If you don't have the tuning instructions I would recommend getting them. The idle adjustment is critical before you can even start the air /fuel mixture. The butterfly has to be perfectly positioned with the idle fuel jet. The illustrations on the instructions help a bunch. After all is said and done I finally did get mine running perfect.
 
Last edited:
hmmmmm? some things to think about there, my return line is brand new and is 8mm pipe (about 3/8s to you lot) so i dont think it can be blocked but not sure what the fuel pressure is at the carb though.
I wonder if an over pressure could cause too much gas to come through, especially since revs are high and the mechanical pump will be pumping fast?
 
Todays lack of progress report and seeing as it was raining i opened the workshop door,fired her up and sat there inside in park and the flatspot is there when there is no load on the engine as well.
I did wonder if the auto was trying to shift at the same time as the secondary kicked in and bogging the engine down or something strange like that but that cant be happening if i am stood still and going nowhere.

If i keep my foot to the floor with the secondary open it does actually kill the engine, but there is no back fire or anything it just dies, if i back off in time then it sorts itself out and then idles like normal!!.
If it does die then it fires straight up again on first turn of the key.

I am going to hazard an optimistic guess that the gas has gone off and simply cannot burn fast enough so is flooding the engine when it gets a large amount of it.
I need to burn it off or drain it and get some fresh stuff in there and see if it makes an improvement before changing any jets, this may mean i have to get it through its MOT test so i can run it on the road and clock some miles up.
How come a 4.2 becomes very fuel efficient when you dont want it to be, that's what i want to know??:rolleyes:
 
My guess is it is starving for gas. Also most mechanical fuel pumps won't over pressure your carb if the return line from the fuel filter to the tank is clear. Mechanical pumps only supply 4 to 7 PSI.
 
Thanks Zr, so like Walkerhound also said above then too much air is as bad as too much fuel then??

The Fuel level float is set right and its parked flat at the moment so looks like re-jetting it may be the favourite, i do wonder if UK gas is any different to US gas? i know the modern stuff is watered down so that may also be contributing to my problem.
 
I can't emphasize enough, read the tuning instructions and UNDERSTAND them. they are very detailed in how to know when to increase or decrease the jet size and when to change which jets. All adjustments should be made with a clean air filter on.
 
We are also assuming that everything else on the engine is mechanically sound. This might be a good time to pull an compression check on all the cylinders. Pretty easy task on the Jeep six.
 
That bit i do know about, the Engine has been rebuilt and probably done about 5 miles at most, so i would hope its compression is okay but you never do know.
Maybe its got an in built self defense mechanism to stop me opening that secondary and revving it until its properly bedded in??????.

Have you got some better tuning instructions other than the sheet they come with Dennis? dont think they mention jet sizes on the one i have just the basic setup.
 
This is the first page of 8. If you can read it well enough let me know and I can scan the other 7.
 

Attachments

All our tuning instructions seems to be coming from the same source. Redline Weber Fuel Management.
 
Thanks guys, working away at the moment so will report back when i get home and get chance.
 
Bought the same carb ( hate it )
Carb is only surposed to have 3lbs fuel pressure,stock pump puts out 5lbs, so you need a regulator and a gage and not just any regulator. I called Webber tech support they were very helpful
Good luck
 
Back
Top