• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Repainting the Factory Hardtop?

scrambler81

Basic User
City
Hammonton
State
NJ
Has anyone tried this?
True story - When I bought mine, the original owner had painted the top with housepaint and a brush. It still has bristles stuck in the paint! Anyway, I've ignored it for almost 22 years, but the paint is really starting to flake off in spots, and it's just dingy and ugly everywhere. I was cleaning off adhesive so I could replace the weatherstrip along the back, and I noticed that some paint is coming off while I'm rubbing. However, I'm using Goo-Gone, and I'm afraid it would take a year to get everything off with that.
So my question is...Is there something safe I can use to strip the paint off without damaging the top? Can it be sanded? I'd like to get it as clean as possible and then have someone spray it black for me.
Any suggestions?

Thanks!
 
I don't think it is as big a problem as you may think.
I repainted mine after repairing a small damaged area with fiberglass repair (wasn't any problem). I pressured washed it inside and out. Bought some Rust'm paint at wall mart. Off white for inside and Hammered Black on outside. Looks like a new one!
 
But what about the stripping part? Mine is covered in house paint, so it's going to need to come off before I can put new paint on.
 
There is a citris (orange) base low toxic stripper on the market that I have used before with pretty good results, although never on fiberglass.??? Not sure if that helps, I would try it in a small spot. There was a post on here not to long ago, about someone Line-x ing there top. You probably wouldn't need to do anything as they would take care of prep. That is if you wanted a textured look.
 
You may be amazed at what hammered black will cover up and make look brand new. As long as the old paint is still sticking to the top/other paint and as long as it is mostly smooth, it should work just fine! Try it...all it will cost you is some time and a couple of $4 rattle cans.
 
you might want to scrub it down with soapy water and a mild 3M scouring pad to prep the surface (and cut into some of that house paint..lol)?

I used the Rustolium hammered black also...and was very pleased with the end result!

I highly recommend the plastic squeeze handle that works with all spray paint cans...
 
Well, I smothered the top in degreaser and scrubbed the crap out of it. Then I did some light sanding on the flaky parts to smooth the area a bit, and then I painted it with that "Hammered" black paint everybody's talking about. Of course, I'm the world's worst spray painter, so we'll see what we've got when it dries. :o It certainly can't look any worse.
 
Well, I put it on, but I don't like it. Even after all these years, all the times I've scrubbed it, and the textured black paint, you can still see brush lines in it. It still looks better than it did before, but I think this summer I'm going to have to strip and do it right. After all these years of looking at that giant whitehead, it sure looks weird with a black top on it. I'll get used to it. :cool:
 
A positive side is now you know where the bad places are such as brush strokes. Don't give up, sand it or spray it with primer to fill them in then respray it:thumbsup:
 
Sanding will probably be the only way to get rid of the bristle marks. Acetone works fairly well to remove latex paint, but it won't help if you've already sprayed it. I used a palm sander on mine to knock down the texture after I coated it with Herculiner. The texture was too thick. I was careful not to cut into the gel coat on the top. Then I sprayed it with black rustoleum.
 
Back
Top