• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Totally ignorant of drivetrains = Me!

FF1115

Basic User
City
Clio
State
SC
I have been on the board here a little while. Never have posted anything. I do have my second ever Scrambler now. I got one when I was 14, rebuilt the 4 banger and ended up selling it for little to nothing. Had no idea what I had. It is still in the family, and one day I will have it again. I bought a built Scrambler and have some very basic questions. BE GENTLE please...I have no idea about transmissions, transfer cases, etc. It does have an Atlas II transfer case, a 5 speed manual transmission, but I don't know that manufacturer or model, AMC 20 axles I think. The engine is the factory Inline 6 / 258. 33x12.5 Parnelli Jones tires. The speedo is off by 20MPH at 55. It will barely maintain speed at 60 mph. My questions are: Do I need to regear? How can I identify the transmission, the axles, the gearing, etc. I am eager to learn and drive this thing. Everything works and most items have been replaced. DUI ignition, Mean Green starter, good paint, YJ fold and tumble seat in the bed, brakes and steering good. I just need more power! Thanks in advance for all the help. Pictures incoming.
 
f3a84b517f1c857d19e6e21f494d8ef5-1.jpg

Transfer Case



 
I'm thinking this is the transmission info? Tag on drivers side. I can't make it out.


 
Show a pic of the gear shift. That will help.

Also, if stock, you should have an AMC 20 rear and Dana 30 in the front (IIRC). Show pics of the differential housings (pumpkins).

As for gears, it may be 2.73 like I had stock in mine. On 33s I bet that has a hard time. There might be a number on the rear housing on the housing to the right of the cover. Mine was beat up and I had to pul the cover and count the gears to get my ratio.

Good luck.
 
This is all I have until I get to the vehicle tonight. So regearing is an option? Or axle swap?
a49f21a60bdae5145a533d40ea583111-1.jpg



 
Can you get more info from the previous owner? That would be the best source if possible. Otherwise you should post up some good photos of everything (axles, transmission (both sides), and engine/bell housing). You can get a guesstimate of the axle gear ratio by lifting the axle and spin the drive shaft and count wheel rotations : drive shaft rotations... to be really sure you may have to pull a differential cover and read the print on the ring gear itself. With an Atlas II in it, I would not assume that anything else is OEM without verification.
 
That looks like a t-5 shifter, but a pic of transmission would help.

And like Spieg said, you can jack up axle and check gear ratio. And yes, changing is an option. How to test:
Block front wheels and jack one of rear wheels off the ground. Tape a piece of string to side of driveshaft so it hangs straight down. Turn wheel 1 revolution. Number and fraction of string wraps around driveshaft is your gear ratio.
May have to rock wheel a bit to get spider gears turning in differential, but should be able to do fairly easy.

If you cant turn jacked up wheel without other wheel turning after several tries, you may have a traction lock axle that still has good clutches in it. This test will still work with one of those but it is a LOT harder to turn the wheel....
 
I checked mine as cbford says and it clearly showed I had 2.7.3 gears. As Dain says you would definitely be lagging like that if you had 2.7.3 with 33's. I struggle a bit on the hills with my 31's. Both regear and axle swaps are options after you verify that it's necessary. I've considered both myself. As I data point I just got quoted $2200 parts and labor to regear both axles, $4000 from another place to do regear and axle upgrades (google amc 20 two piece axle), and $7000 for two new Dana 44 axles with the gear ratio that I'm looking at. Other places in America will probably cheaper, sometimes much cheaper for the regear.

Also, if you're not familiar with it you should check out gear ratio calculators:

http://www.quadratec.com/jeep_knowledgebase/article-26.htm

I was going to go with 4.11's, but Jim wisely talked me down to a higher (numerically lower) ratio as the 258 would be screaming on the highway.
 
I can't imagine swapping in an Atlas transfer case and not doing other upgrades. I'd be shocked if the rest of the drive train is stock...however, I've been wrong before.
 
I see a twin stick.. did you check to see if the rear is in 2wd high. Not 2wd low?

Sent from my SM-N910P
 
Looks like gr8dain was right on with the AMC 20 rear and Dana 30 front. I tied the string method and got 1:1.75 and multiplied by 2 for the open diff / spider gears turning for a 3.55 gear. The transmission had Borg Warner on the side and does look like a T5. I have a call in to the original owner, but am certain he hired it out. Thanks for the help!
 
Those gears are low enough that I am surprised about not being able to get to 60. Makes me wonder about my slight upgrade (haven't been able to drive it yet).

By the way, do you know if it is one piece axles in the rear?
 
I only jacked up one tire and it spun freely. I don't have a clue. Is it easy to tell?


 
I only jacked up one tire and it spun freely. I don't have a clue. Is it easy to tell?

Yes. With the center caps off, is the hub flush, or does it stick out through the hole in the center of the wheel? If flush, one piece axles. Which is stronger.
 
oops. I always forget the x2, or 2 revolutions. Sorry.

But, unless your 258 is fresh and pretty stout, I am not surprised 33s with 3.54's are a little slow with the t5. 4th gear would be good on flats, marginal on hills and 5th would lug all the time would be my opinion. 4.11 gears would wake that thing up pretty well.
 
Back
Top