• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Weber Jetting questions

twmattox

Legacy Registered User
City
Arcadia
State
IN
Need assistance from those who bought the Weber 32/36 Redline/Weber kit. I am rebuilding a Weber (not from the kit) that was given to me. I need to make sure I am putting the correct jets in. Teh Redline/Weber tech line will not give me all the "answers". To date what I have found is:

Primary Idle: 75 (possibly upgrade to 80)
Secondary Idle: 60
Primary Main: 145
Secondary Main: 145
Emulsion Tubes (both sides): F-50

What I still need to verify are the air correctors. When you take off the air cleaner and peek down the throat of the carb, they are the little circles peeking back at you from a small opening in front of the throat of the carb. With a good flash light you should be able to make out numbers like 170 or 160. Please look and tell me what you find...
Picture attached.
 
That pic is what they look like without my reading glasses:D :D

Seriously, though, mine is a 38 and probably wouldn't do you much good. although, I'd be glad to give you the jet sizes for mine.

Paul
 
Yeah, camera was too close to focus well. However, if I get too far away, no body could see what I am talking about.

It may not be relevant, but if it is not too much trouble, would you mind giving me your numbers?

Still looking for someone with a 32/36 too...
 
I got a 32/36 dgev at home. It is in a box out in the garge, and I will have to dig for it. But might be able to check it out.

I will try tomorrow.

Carl
 
You would be my hero. Apparently, these jet settings are a closely guarded secret. I was able to find most of them out, just need these last few...
 
Looks like I have a 170 on the 32 side and a 120 on the 36 side. Kind of wierd, but that is what it looks like to me. Seems to agree with that page listed above, but just a little different.

Might be my bad eyes but it looks like 120.

Carl
 
The link above worked well, but "Tom" from redline/weber indicated that is how they get them from the "factory". They then re-jet them to specific applications, so our jets may be different from "factory" spec.

I am just trying to see how they jet these...
 
twmattox said:
The link above worked well, but "Tom" from redline/weber indicated that is how they get them from the "factory". They then re-jet them to specific applications, so our jets may be different from "factory" spec.

I am just trying to see how they jet these...

That's more valuable info than the data I sent. Thanks for the update.
Paul
 
I put the numbers in the post above.

170 on the 32 side and 120 on the 36 side.

Was there more than that, that you needed. If you really need I can send the carb your way to have it checked out. I could probably pull it apart if you needed more than that.

Carl
 
No Problem.

Was there anything else that you needed to know about the Carb. It is actually at a point in the garage where I can lay my hands on it it if you need me to.

Carl
 
If you are still in a position to look at the carb, I do have additional questions...

1) Can you tell me primary and secondary idle jet sizes (the screws are easily accessable on the side of the carb). The primary is on hte passenger (engine) side and the secondary on the driver side. Just unscrew, and the jet is connected to the back side of the screw. The number should be printed on the side of the jet. Should be something like: 70, 75, or 80 for primary and 60 for secondary.

2) Can you tell me the size of the pump jet. This is the nozzle looking thing that points down (from the top) and squirts gas into the throat of the carb. The number should be printed on the top (it is kind of small). Should be like 50 or 55.

I understand if you don't want to tackle this, but would greatly appreciate the help...
 
I will have to go and dig the Carb out of the garage this weekend. If I do not get back to you soon. Shoot me a friendly reminder via PM.

I will try to leave my self a message to get this done.

Carl
 
Back
Top