• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Fly wheel compatability

Blawesome

Legacy Registered User
City
Leander
State
TX
Hey all!

I just got on to the blog and love the information so far. A lot of great 8s out there and I hope to get my running smooth through the help I can get from y'all.

Quick History:
Blawesome is an 81 scrambler. I'm not a great mechanic but I can wrench when I have to. I just had the clutch replaced and the mechanic I work with realligned the transmission to the engine. Apparently there was a dowel missing so he replaced that as well. When he did, the engine and transmission were perfectly alligned.

The problem:
Now that the two are synced up my starter is acting funny. It grinds like there is no tomorrow.

My thought:
I have tried shimming with no success. I have verified the correct starter is in there. Could I possibly have the wrong fly wheel? Can the 11 inch fly wheel fit in the same housing as the 10.5?

Lucky for me I have a lot of hills to park on so I just roll down and pop the clutch to start it, saving the starter teeth whenever possible.

Anyone have any ideas on what the problem might be?

Thanks for the help!
Jason
 
put a new bendix on the starter and give it try. then you may have to put a new ring gear on the fly wheel.
 
i've tried to replacing the bendix with no luck. It's almost as if the starter is hitting the face of the flywheel instead of sliding right beside it and meshing with the teeth.

What size fly wheel should I have on the jeep to begin with?
 
What motor and trans is it? When you say eleven and ten inch flywheel are you talking about the od of the flywheel or the od of the clutch disk??? my flywheel is thirteen inch across???? I have a t four trans and a four.two Do you know for a fact that the ring gear is one hundrend percent good?? Mine had a 6 inch section where the teeth were gone and if it got hung there it sounded awful and would not crank with out bumping the motor over some.
 
Last edited:
I have the original 258 inline and the borg warner T176 trans. I'm trying to find a diagram online to see how to disassemble it. It would make sense that the fly wheel is chewed up. It sounds so bad that I'm thinking it's not even the right one, but I don't know if another could fit in there. I priced new ones online and its on $36.00 from Morris4x4.
 
When you have it at home and can remove the starter crank on it till it hangs and wont turn over anymore and pull your starter and see what the teeth look like around the hole where the starter was in.

Mine was clearly lacking teeth where it would not turn over.
 
I had a similar problem with my current CJ8. to give you the "quick" answer.. I tried shimming it in/out with no luck.. as the CJ starter mounting points are fixed. Got no good solutions on mulitple Jeep forums. I finally broke down and called the service department at Collins Brothers and asked for an idea. Tech on the phone told me he'd seen the problem before, but rarely. Bottom line: I had to "clock" the starter in to the flywheel. I did this by drilling out one of the mounting holes (making it wider than it was, allowing the starter to rotate a hair inwards toward the block), put a pencil/dowel of wood in the hole, and then back filled the rest of the hole with JB weld.. I then cut/drilled out the pencil/dowel.. the result was a slightly adjusted mounting hole that allowed the starter to sit JUST a bit closer to the block one of the two mounts..

I have since disassembled the truck for a frame off and swapped in a 4.0.. that said, I was using the same flywheel back (including the CJ bellhousing).. to try a better solution to this, I bought a new (used) bellhousing, hoping that the slight shim problem was a matter of warping/casting in the original bellhousing (and it's worn out starter mounting holes). Not sure yet if this is the best solution, but it's what I'm trying.

Hope that helps.
 
The guys can correct me if I am wrong but I think you may have a miss match of parts. An 81 with the 258 did not come with a T176, at least mine didn't nor did any of the 81's I have seen. The missing dowel pin is a give away that whoever did the tranny upgrade from the SR4 had issues.

All of this is pure speculation, you/we need some part numbers on the flywheel, clutch parts, and starter to be sure. If you pull it back apart shove an AX15 with clocking ring to adapt the Dana 300, you'll love having a 5th gear and can put lower gearing in the axles for more power/acceleration.

Keep us posted and good luck.

Richard
 
I have the original 258 inline and the borg warner T176 trans. Morris4x4.

Just for reference, you have a Tremec T176, not a Borg-Warner. Borg-Warner was the manufacturer of the T4/T5/SR4.

The guys can correct me if I am wrong but I think you may have a miss match of parts. An 81 with the 258 did not come with a T176, at least mine didn't nor did any of the 81's I have seen.

The T176 was available from 1980-1986.
 
From the Novak site

The Tremec T176 transmission was the optional four-speed transmission found in 1980 to 1986 Jeep CJ models. It is a good transmission when well maintained and has often been adapted to V8 and V6 power.

My 81 cj7 Laredo came with a 304/176/300
 
I had a similar problem with my current CJ8. to give you the "quick" answer.. I tried shimming it in/out with no luck.. as the CJ starter mounting points are fixed. Got no good solutions on mulitple Jeep forums. I finally broke down and called the service department at Collins Brothers and asked for an idea. Tech on the phone told me he'd seen the problem before, but rarely. Bottom line: I had to "clock" the starter in to the flywheel. I did this by drilling out one of the mounting holes (making it wider than it was, allowing the starter to rotate a hair inwards toward the block), put a pencil/dowel of wood in the hole, and then back filled the rest of the hole with JB weld.. I then cut/drilled out the pencil/dowel.. the result was a slightly adjusted mounting hole that allowed the starter to sit JUST a bit closer to the block one of the two mounts..

I have since disassembled the truck for a frame off and swapped in a 4.0.. that said, I was using the same flywheel back (including the CJ bellhousing).. to try a better solution to this, I bought a new (used) bellhousing, hoping that the slight shim problem was a matter of warping/casting in the original bellhousing (and it's worn out starter mounting holes). Not sure yet if this is the best solution, but it's what I'm trying.

Hope that helps.


This makes sense. It is an option I have thought about but I may have to use it as a last result. I'll let you know where I end up.

Thanks!
 
The guys can correct me if I am wrong but I think you may have a miss match of parts. An 81 with the 258 did not come with a T176, at least mine didn't nor did any of the 81's I have seen. The missing dowel pin is a give away that whoever did the tranny upgrade from the SR4 had issues.

All of this is pure speculation, you/we need some part numbers on the flywheel, clutch parts, and starter to be sure. If you pull it back apart shove an AX15 with clocking ring to adapt the Dana 300, you'll love having a 5th gear and can put lower gearing in the axles for more power/acceleration.

Keep us posted and good luck.

Richard

Some quick history: I go this Scrambler from a high school shop class. Frankestein had less superglue on him than Blawesome! It would not surprise me at all to find make shift adaptations. I also have a low/high gear which apparently wasn't an option either. (?)
 
If I do have a make shift unit here it runs rather well. I changed out the exhaust/intake gaskets and it required the 81 parts. However, when I changed the valve cover gasket I had to go to an 80 model engine to get the right one. It was very obvious the 81 wouldnt work. What are y'alls thoughts there?
 
Back
Top