• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. J

    ACME CJ8 hard top I think?

    Picture of my acme top.
  2. J

    Someone called it a TJ 6

    :fingerscrossed::popcorn:
  3. J

    Someone called it a TJ 6

    Can they sleeve the cylinder? Hate to see a sub-par motor go in with all the work you did on the jeep.
  4. J

    Epic fails

    Epic fail is not the vehicle, it's the owner:ROFLMAO:
  5. J

    What's on your Work Bench?

    Got delivered last week. Because of work load never got a chance to check them out. What a surprise, beautiful side boards, very well wrapped. Wrapped so good I never undid the second board. Wrapped and re-boxed for winter product. Many thanks (more than you can know) to Jeep Addict. Much...
  6. J

    Tailgate latch ideas?

    You could spot weld a shim on the latch. Have bottom slopped (like a ramp) so it pulls the door tighter as the latch goes down
  7. J

    Rosco1974's 1985 CJ7 Project

    Go to Autobody101.com. Post under auto body and paint. Good group of guys with a ton of knowledge. They'll ask questions and you should get some good answers. Groups a lot like this group. Best to find out before you move on.
  8. J

    What's on your Work Bench?

    She did a great job. Amazing what they can do today.
  9. J

    Fuel fill hose and vent line.

    If I remember I used 1" copper water line to join pieces together . Used 15 gal tank hoses and cut 2 to fit the bend. The gas tank I used was a aluminum 25 gal tank. Couldn't find flexable hose that was bendable and gas resistant.
  10. J

    Crappy factory paint and moldy interior

    Also ask CB. He's brought some dashes that were in worst shape back to life.
  11. J

    Timing question

    If the vac hose has vacuum to it, it's advancing the timing that's why you don't see the timing mark. Depending on the setup (manifold vac, has vacuum at idle. Ported doesn't have vacuum at idle, but gets vacuum as you give it throttle). Manifold vacuum starts the timing curve before you step...
  12. J

    Meet Red, my 81 Restomod Build

    Put one in my cj7 to cj8 build. They make a mod that almost centers the shifter lever. Makes running through the gears faster, but holds the lever in what ever gear you have it in. I love the shifter, especially compared to the B&M shifter I had in it before.
  13. J

    Stickers!

    She's one of the few (good parents). It's fun mentioning how to start my jeep to them (manual choke).
  14. J

    Advice on an '81 for sale

    It's not a Dana 18 (rear would be offset on pass side)
  15. J

    Scrambler New Body Tub Rust

    Probably just moisture that condensed on the floor. Looks like just surface rust. Just give it a good sanding and shoot epoxy primer on it. Make sure you sand where you apply the new epoxy. Jeep looks nice.
  16. J

    Starter solenoid wire identification

    I don't know if your ground cable goes from the batt to the starter bolt. If it does connect one end of the black jumper cable to the neg battery terminal, other end to the starter bolt. Disconnect the blue wire from the solenoid. Make sure the jeep is in neutral or park. Put the key in the...
  17. J

    Starter solenoid wire identification

    A easy to make sure you have a ground to the engine is take a pair of battery jumpers. Use the jumper ground cable on the batt neg. post. Other end clip onto a starter motor bolt. You now by passed the ground cables and you know you have a temp ground to the engine.
  18. J

    Starter solenoid wire identification

    He is correct on having the jeep in neutral or park and jumping across the solenoid (actually by passing the solenoid) will cause the starter motor to crank. If not you probably have a bad ground at the starter, froze motor, bad starter or more than likely bad battery/ground cables. If you...
  19. J

    Brake Drums out of Round?

    I wouldn't play games. I'd take them to a shop and have them turned. If it just a minor high spot, you won't take that much off. Hopefully you'll still have a good, long life with them. Not worth waiting for them to wear to wait for them to hopefully wear round. I remember many years ago...
  20. J

    Pouring oil into my frame to preserve it longer!

    Very tough, and dense. A finger can push it in about 3/8". Need to hammer a flat blade screw driver to tear out chunks.
Back
Top