Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
AMC Jeep 360 V8 w/ motorcraft 2150, trouble with initial stumble off idle und...
Before I swapped the carburetor out for another 2150, I spent a few more late evenings of work on it and finally got the problem straightened out. There was a very small vacuum leak at the firewall where the...
Be careful lifting the tub from the very front and rear like that. The tubs easily bend in the door section, even slightly, and can cause major fitment issues down the road.
I would steer clear of Herculiner; it could possibly be the worst bedliner I have personally ever seen. Its texture traps dirt/sand making it almost impossible to clean, it fades, and when it dries the texture can become very sharp. I am not a fan of bedliner in a Scrambler but if you must, I...
Haven't done a compression check on the engine yet. It's idles great and runs very smooth at all RPMs, except for right off idle. I will do a compression check this weekend on it. I would think weak compression in a cylinder would cause more issues than just the off idle stumble?
Sent via...
Dist. advance is working, I can pull a vacuum on it with the engine running and it does increase the engine RPMs. Not sure on my total advance, I just have a basic timing light and no timing tape on the harmonic balancer. I played with the accelerator pump rod placement with the ported vac...
AMC Jeep 360 V8 w/ motorcraft 2150, trouble with initial stumble off idle und...
Set timing this morning to 10 degrees and hooked the advance back up to the ported source, no change. It still has the hesitation right off idle. From what I have been reading the manifold vs ported distributor...
I'm needing some direction with an issue I'm having on my 1979 Jeep Cherokee S 4 door. The Jeep has what appears to be a stock rebuilt 360 with the 2 barrel Motorcraft 2150 carburetor. The Jeep had sat for several years before I purchased it.
The issue I'm having is, right off idle when you hit...
Dug the '45 MB out of one of the sheds this afternoon and took it for a quick spin; still need to address the brakes. I'm committed to getting one of my postals done before I bring the MB in for work.
Sent via signal flare
Not to hijack your thread but what brand and size of lift are you going with on your XJ? I am in the market for a 3" lift for my '00 XJ. The plan is to put a set of 16x8 LJ Rubicon Moab rims I have and the old factory size tires off of my '05 LJ Rubihara. Mine mainly sees daily driver duty so...
BD tops are more expensive but are MUCH better quality in terms of fitment, material, and hardware than Bestop. Plus, BD tops are made in the USA; which bestop is not.
You are correct, some of the Commanches and police package XJs had a column shift. It seems these columns can be pretty tough to find. I did see where I can still get the cable and cable bracket that mounts to the bell housing from Chrysler. All else fails I may try rigging something up with...
As with AMC, you could order a Jeep with about any combination of options you could imagine. You could get a base model CJ with a clock and tach. My '85 CJ7 is a base model and original came as a soft top only Jeep (no doors strikers installed or door limiting strap brackets mounted on the...
I am looking into another 4.0/AW4 drivetrain swap from a '93 Jeep Cherokee XJ, this time into one of my CJ7's. The Jeep this is drivetrain will be replacing has a 4.2 with the TF999 auto. The Jeep currently has a B&M floor mounted ratchet shifter, which I would like to replace with an original...
x3 on the vacuum leak at the intake manifold. I fought a miss that I couldn't figure out on my '85 CJ7 back when I first bought it 10 years ago and it was still carbureted. Turned out the back two bolts on the intake near the firewall were slightly loose. Tightened them back up and it took care...
Took the Cherokee out a few weeks ago to check on a few tree piles we had burning:
Haven't had time to really clean it up yet but you can see where I have been people have been rubbing up against it on the front 1/3 how decent the paint looks underneath!
No major plans for this one yet...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.