Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
I am with mysunnshine on this one.
The low pressure caused by outside tank pump that is sucking fuel up through the stock sender, combined with the higher temp is probably causing aeration at pump. Not enough to stop the pump, but enough to impact fuel pressure.
I did the math on mine to see...
This answers a lot of the questions raised.
http://www.nmma.org/lib/docs/nmma/gr/environmental/E20_Position_Paper.doc
Basically, it is not the ethanol; it is the water that the ethanol holds in the fuel that causes oxidation changes, builds static electricity and is general trouble for filters...
Soapy water, yes. And it doesn't take much soap.
Its not possible to have too much since you are going to squeegee it all out.
I trimmed them and mocked them up.
I used tape and marks on the mask cover over the actual decals to get them aligned where I wanted (above).
Then peeled the...
I expect to find more, but this one kind of surprised me. I haven't re-geared (3:31), its an open differential and I haven't put larger tires on yet. First hard shift into second and POW.
Guess I will swap yolk to u-bolts to go along with the welded tubes, used locker and 4:56 gears I am...
That thread is pretty good for the YJ frame swap.
If someone decides to try it and needs pictures that are not shown there let me know. This is done on mine and works great. Definitely a big improvement in wiper linkage and arms. I also have the YJ motor to CJ delay box/switch wire color match...
I did some of this upgrade too. The stock bracket will need to be modified in terms of bolt spacing as well. I don't remember how much off top of my head, but it was required.
I also found this, which is $10 less than the tuff stuff clevis parts/extensions but are same size/thread/quality...
oops. I always forget the x2, or 2 revolutions. Sorry.
But, unless your 258 is fresh and pretty stout, I am not surprised 33s with 3.54's are a little slow with the t5. 4th gear would be good on flats, marginal on hills and 5th would lug all the time would be my opinion. 4.11 gears would wake...
That looks like a t-5 shifter, but a pic of transmission would help.
And like Spieg said, you can jack up axle and check gear ratio. And yes, changing is an option. How to test:
Block front wheels and jack one of rear wheels off the ground. Tape a piece of string to side of driveshaft so it...
Transmissions don't just get a torque rating; it is a torque rating at x weight (GVWR). Here are specs for some of the manual boxes talked about on here:
ax15 300ft lbs @ 7000 lbs
nv3550 315ft lbs @ 7300 lbs
nv4500 460ft lbs @ 16000 lbs
The weight rating is important because it allows...
The venturi size is cast in, no changing. But, with headers, an overbore with a little cam, a 1.21 may be ok for you. Just work through jet choice, and adjust the accelerator pump down low so it squirts less and then raise adjustment up as you experiment.
I just read this the second time. I am not sure I understand the problem. I could make some assumptions, but I will ask some questions instead.
Are you saying that with the new carb/cam, that your engine is turning what you feel are too many rpms in forward gears?
Do you have a accurate...
If you get REALLY technical:
Keeping your shocks/springs at stock width and using a wider than stock track width axle would require a slightly higher spring rate/shock pressure to keep factory load and rebound characteristics for suspension.
But since we are not talking about a race car and...
The 40p's are a bit better I think, other than the header issues. They have a slightly smaller combustion chamber, no thermactor ports to mess up flow or quench area so you get slightly higher compression without detonation with them.
Their second weak spot is valve springs, but you are going...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.