Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
Glad to hear you went in early! Nothing worse than waiting on those couple of days it takes to run tests and what not to get results back. I absolutely hate the "C" word... As others have said, cheers to a speedy recovery!
Planning 4.0 Head & FI swap
To try and answer some of your questions I think it would be easier for you to decide if you are wanting to go OBD1 or OBD2. OBD1 is obviously a simpler system (5 wires to fire).
Regardless if you go OBD1 or 2, you will need the distributor for that system...
Been a while but finally back at more sheet metal replacement. Measured 20 times, clamped, remeasured, check to make sure its all square, remeasured several times, finished beer, remeasured to ensure its as close to perfect as possible, then started welding.
More issues with the MD Juan side...
I'm running a Thrush Hush on my '84 CJ7 with an AMC 360, 2.5" into a single 3". Has a nice quiet rumble at idle and sounds great when you open it up but still not overly loud. We use this Jeep on our trails and to get out deer hunting so I wanted something fairly quiet. Definitely quieter than...
If you are not going to replace both lines then I would at the very least recommend replacing both o-rings at the end of the lines.
Thought those adapters looked out of place on the box!
Threads showing on the nuts at the end of the lines is perfectly fine. The o-ring is sealing it at the...
I'm not positive but the brass bushing inside the port looks like something used to convert to the older style flared fittings. I would see if that gold ring can come out.
It almost looks like both the ports on the steering box have some sort of fitting installed. I don't remember there being...
Mine have all been direct bolt in swaps using the original CJ o-ring style power steering lines. No adapters or custom lines needed. I'm not sure I'm following you on your two posts about which line is to big? Is it the line that threads into the back of the power steering pump reservoir or the...
I would think you should be able to make the Lokar cable work. Not your exact swap but I just used one in my '84 CJ7 that I swapped an AMC 360 in w/ the TF999 along with the Ididit column cable shift linkage and it worked great. Definitely much simpler than the original linkage. With the...
Just used a regular drill bit and drilled all the way through on this area. I will be using the holes in the panel still attached to the jeep for my new spot welds.
Off!
No rust through on this piece but the capture nut is broken so I needed to get into the panel anyways:
No pictures but...
Plenty of clamps are a must:
when spot welding, I scrape the hole clean of weld through primer and put a clamp or two right on either side of where I will be welding.
Spot welds almost all in and clamps/braces removed. The spot welding was all done from inside the wheel well and underneath...
Back at it again with the rust repair and panel replacement. Motivation is finally back after fighting with the junk MD Juan side panels and working on a few other projects.
I'm going to have to get creative with how to graft the top edge of the replacement side panels into the original panels...
The ECU is up under the dash above the heater box. It's in approximately the same location as the original carter BBD computer. I ran the wiring through the original hole in the firewall where the carter BBD wiring went through near the battery above the heater hoses. I did have to slightly...
Planning 4.0 Head & FI swap
On my '85 CJ7 with a 4.0 MPFI head swap I just used JB weld with water soluble packing peanuts behind it and have not had any issues. Just make sure to have the area inside the coolant passages is really clean beforehand. The head was cleaned and rebuilt...
Bolts to the frame and crossmember in the original locations. Also has a spot to drill an optional 3rd bolt through the crossmember for added strength.
Sent via smoke signal
I'm running that same Mountain Offroad brace on all my CJ's with the H1 27-7595 steering box. It bolts up perfect, no modifications necessary.
Sent via smoke signal
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.