• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

20 Gal Factory Fuel Tank Delima

TJNICK97

TJNICK97
City
SLIDELL
State
LA
I Have An 82 Cj8 With A Factory 20 Gal Fuel Tank, My Filler And Vent Lines Are Bad And No One Makes One.......here Is Another Problem, I Was Going To Make It Easy And Replace It W/ The Poly 21 Gal But The Manuf. Says It Will Not Fit A Cj8 Because It Will Hit The Rear End.....my Jeep Is Lifted About 4.5 In The Rear..........i Dont Have The Time Or Meens For A Custom Tank

Any Suggestions

Help Please.....
I Am So Close To Driving And This Stupid Delima Is Holding Me Up
 
I put the 20gal. poly tank in my -8. There are two, approx 4" drop brackets which bolt to the existing tank skid plate. With some applied geometry you can make the tank fit and miss the diff cover....
 
If it is just the hoses, I'm sure you can find a way to make replacements. The vent line should be very easy since it is still relatively small. The filler is a little bit tougher to duplicate. Problem with it is that when you get to that size fuel hose, iti is generally to stiff. However, if you check around, you should be able to find something that will work. I would start with a place that specializes in rubber hoses and grommet.
 
The filler and vent lines are not available from the manufacturer anymore, I've tried. The problem is one end is something like 1" and the other is 1 1/4". I've seen them on ebay so that's an option. Another suggestion is go to a Hose supply company and they can make you one. A piece of 1 1/4" & 1" hose crimped together using an adapter coupler. I've got the 20gal tank with this set up and it fills and vents just fine. Good Luck
 
Last edited:
I just went thru the same crisis with my junk last month. As I recall, it 3/4 and 1" at the filler and 1" and 1 1/4 at the tank. I just got some hose and welded some U-bends together with some adapters. When I'm back up in the mountains where I keep it now, I'll shoot some pics of my mods.
 
I'd appreciate a heads up on your adaptation. I've got an 81 and while 21 gallon tanks are offered with hoses, they only cover 82+. What makes an 81 so different? Thanks!:confused:
 
Did the tank manuf. tell you the 21 gal ply wouldn't fit because of your lift?

I've got the 21 gal poly tank from 4WD Hardware on mine and it fits fine. I did have to cut a little clearance into the lip of the skidplate extension that comes with the tank, but it was minor and doesn't affect the skidplate at all, just a little bit off the lip where the skidplate extension connects to the skidplate. Without that little bit of clearance the lip would have hit the diff.

Hoses for the stock 15-gal tank work with the 21-gal poly tank.

Only disappointment is the sender 4WD sells for the 21-gal tank, mine has failed after only two years, now I have to drop the tank to replace it.
 
Difference

The difference with the 81 and the rest of the cj8's is the metal filler neck. The filler neck on the 81's is short like a regular cj, and all the rest of the 8's have a long filler neck. It is about 6" longer. I looked for a long time before I finally found a long one. If you can find one they are pricey. I had to end up paying 50 bucks for mine. GOOD LUCK!

Don
 
I have to drop my 21 gallon tank next week to replace the sender, I'll post some photos then.
 
I have a Factory 20 gal tank. I went to a Industrial Hose Company and purchased Marine Fuel and Exhaust Hose in the correct size. I had a really tough time getting the 2 hoses to go through the support member that was there so I drilled a new hole for one of the hoses. I picked up 3 feet of each which was more than I needed, but was scrape to them.

If you need pics let me know.

Vinny
 
Maybe mine was different than yours but at the fill neck it's 1" and 3/4" and at the tank it's 1" and 1 1/4" as I recall. Did you just clamp down the 1 1/4" to the 1" at the full neck?
 
You are correct. I did crank down on the hoses, I might have even used 2 clamps, to make sure I had a good seal.

Vinny
 
I dropped my tank today to fix the gauge sender so here are some pictures of how the 21-gal poly tank fits in the Scrambler.

First pic shows how I cut a bit of the lip off the skidplate (and a matching piece off the skidplate extension) so the skidplate and extension can clear the differential.

Second pic shows how I had to add 1/2" spacers between the extension and the skidplate (only on the rear), to allow enough clearance between the filler tubes and the floor. Maybe a different sender/pickup unit would clear without this extra 1/2" but the one 4WD hardware sells to go with this tank doesn't clear.

This tank works with the stock hoses for the 15-gallon tank so there's no messing around with custom hoses.

Oh and what was wrong with my sender? The float developed a leak and filled with gas so it was always on the bottom reading empty. This is the 4WD sender that they sell with the tank.

attachment.php


attachment.php
 
Last edited:
Back
Top