• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Alternatives to the 258 carbureted engine

Upgrade the 258 on the cheap

There are lots of alternatives to do, but the question is what you want to pay and how much of it can you do yourself.

If I had the time and space, my jeep would have a 4.0L in it. Pure and simple, but because I work and travel a lot and only have a 1 car garage now, I have opted for a continual upgrade approach.

In 2000, I upgraded to the 4.0L head right after I had my thanksgiving turkey. Junkyard head, bolts, and complete valve job, along with the the peanut-stuff/marine-tex gray method cost $250 or thereabouts.

While I was at it, I swapped the borla header on ($200) and a weber carb ($200). It was a tremendous improvement. I added an MSD ignition (120) and ford TFI upgrade ($60)

I then sold the weber for $190, purchased a clifford squarebore manifold used ($50) and a holley 390 4bbl ($200) and it made even more power.

Today, I am finalizing the purchase of a howell tbi system. The total cost to my door is $1150 with carb certification and a special chip for all my mods.

What did I learn? Well, total input to the engine is somewhere to the tune of $1700 after I sell off my holley 390. I am expecting it to make more power than just the bolt on EFI with same reliabliity. My engine has never skipped a beat in 5 years and 50k miles with these mods. I think the howell will only add to my pleasure of having the jeep.
 
My brother did a Wankle into anMB when he was in High School (late 70s), No bottom end at all. Not a good choice at all, but maybe they're better now.

When I lived in VA in the late 70s there was a guy who totally dominated the sand drags in the area with an old pontiac 4 cyl, with the staging against the built v8s he often took top overall.

Personally I wouldn't choose either a wankle or a 4 cyl, but to each their own...
 
jachristner said:
What is involved in swapping a 4.0 in place of the original 258? Will the 4.0 motor mounts bolt straight into the CJ, the 258 mounts straight to the 4.0 or does it require custom mounts?

It is close to a straight bolt in - you have to enlarge one hole on one side only. Go to cjoffroad.com

Go there for a forum section devoted to this swap.

There must be thousands of cj's out there with the 4.0 engine. I did my swap seven years ago. My major advice would be to go with the HO engine with ODBI ecu (about 91 through 96).

Later, Ken
 
trust said:
When I lived in VA in the late 70s there was a guy who totally dominated the sand drags in the area with an old pontiac 4 cyl, with the staging against the built v8s he often took top overall....
You were here then?? That guy, Terry Hall (I'm still in touch with him), blew that motor running against me....never ran it again. It's still in his barn (the Jeep that is). He left parts down half the track.
 
The Wankel idea was a yolk, so to speak:rolleyes: However, you could make a 4 into a screamer, or just go with the crowd and do a small block. yawnnn.
Paul
 
mtruckstuff said:
The Wankel idea was a yolk, so to speak:rolleyes: However, you could make a 4 into a screamer, or just go with the crowd and do a small block. yawnnn.
Paul

Yeah, there's nothing quite like a 4 banger screaming at 5,000rpm to make it's peak torque in order to climb an obstacle at .5mph. :eek:

I'll take the displacement, thank you very much. :D
 
Well, maybe..... if it was built in America, no Canadian small block for me!! Hi Boom!:D :D
 
John N said:
You were here then?? That guy, Terry Hall (I'm still in touch with him), blew that motor running against me....never ran it again. It's still in his barn (the Jeep that is). He left parts down half the track.

Yup, labor day 76 through mid August 80. I was an original member of the Peninsula Mudslingers club in Newport News/Hampton. We used to go to some of the club racing events, Bodacious something or other was the one I remember the most, he used to do very well with the 4 cyl in the drags there. Why didn't he rebuild and continue? A buddy ran a v6 commando but never did worth a hoot, I think his wife might have trophied once. What were you running back then?
 
Back
Top