• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Anyone done a 258 with HO 4.0 head EFI Conversion?

Grantshire

Legacy Registered User
Member
City
Richmond
State
VA
I have been squirreling parts away for some time to do a 4.0 head swap on a 258 for my Scrambler. I have a complete 258 and was considering having it professionally built with the 4.0 head but am torn between a 4 barrel intake setup, Webber or going with a Howell EFI kit. I know people have put the Howell kit on their stock 4.2's but what about a built up engine with the 4.0 head? I would prefer not the drop a 360 into my Scrambler (I think the power of the 258/4.0 head setup is almost as good as a V8) and the 6 cylinder should be a little better on fuel economy.

Has anyone does this? How is the gas mileage? Other comments? I will be running a 4.10 gears, manual OD (T5 or AX15) and 35" BFG tires.

:cheers:

Richard
 
I'm considering the same swap. The local "expert" here gets $2,300 for the turn key swap with warranty. $800 of it is labor. I have the stock 4.2 with a Webber carb (not happy with it) and get 11mpg regardless of 2wd or 4wd. I don't expect much more if any with the Howell conversion. I just want reliability. I'd almost prefer the stock carb, but don't have one. My 79 CJ-5 with 258 had tons of power and no issues. Like you, I'm not stock on lift. I have a 4" suspension lift on 33's. My fifth gear is of no use unless I'm going down hill with the wind at my back. I've been warned by many local Jeepers to be very careful if doing the Howell conversion myself. ??? More than likely, I'll pay the money. Keep us posted on which route you go and tell us your experience with it. I'll do the same.
 
I'm considering the same swap. The local "expert" here gets $2,300 for the turn key swap with warranty. $800 of it is labor. I have the stock 4.2 with a Webber carb (not happy with it) and get 11mpg regardless of 2wd or 4wd. I don't expect much more if any with the Howell conversion. I just want reliability. I'd almost prefer the stock carb, but don't have one. My 79 CJ-5 with 258 had tons of power and no issues. Like you, I'm not stock on lift. I have a 4" suspension lift on 33's. My fifth gear is of no use unless I'm going down hill with the wind at my back. I've been warned by many local Jeepers to be very careful if doing the Howell conversion myself. ??? More than likely, I'll pay the money. Keep us posted on which route you go and tell us your experience with it. I'll do the same.

What gears do you have?

my 1982 has 4.2L, T-5, 3.54 gears, 31"AT's, TFI, Weber 38/38 (properly tuned and jetted). Plus I am at 7000 feet elevation, so I am down 30% on horsepower. I drive from Flagstaff to Sedona daily...and I am doing about 17MPG driving up and down the hill. Closer to 21-23 on pure highway runs.
 
Wow! I'm impressed. I don't know what gears I have and I don't know what Weber either. I can say it's a fat thing that can't use the stock air cleaner. I haven't torn into the guts yet....but will shortly. I just got this jeep on Thanksgiving. I just did the back road from Lake Pleasent to Crown King then up to Prescott on the Senator Hwy and then into Flag last weekend. Mine spitted and sputtered the whole way up and most the way down. I've only put about 3 to 5000 miles on the jeep since I bought it and haven't gone over 11mpg yet. I'd love to hear your fix, because I want to stay as stock on the engine as I can. I'm sure Grantshire would too.
 
Currently mine has a bone stock 258 with HEI. I swapped out the stock T4 for a custom built T5 (all the upgrades possible for the Jeep T5 professionally installed to come as close aspossible to WC T5) to have OD and got rid of the crappy stock axles with 2.72 gearing. Swapped in FSJ Dana 44's front and back with 4.10 gears (picked for 33" tires) and run 35" x12.50 BFG AT's. With the stock engine it will run 70 mph on flat ground but does not like strong head winds. I think it is more a function of the crappy stock carb than anything else, I know several guys who have Jeeps with 258/4.0 head setups and they run like a V8.

They are all carb setups so my question about EFI with the 258/4.0 head combo still stands...
 
Wow! I'm impressed. I don't know what gears I have and I don't know what Weber either. I can say it's a fat thing that can't use the stock air cleaner. I haven't torn into the guts yet....but will shortly. I just got this jeep on Thanksgiving. I just did the back road from Lake Pleasent to Crown King then up to Prescott on the Senator Hwy and then into Flag last weekend. Mine spitted and sputtered the whole way up and most the way down. I've only put about 3 to 5000 miles on the jeep since I bought it and haven't gone over 11mpg yet. I'd love to hear your fix, because I want to stay as stock on the engine as I can. I'm sure Grantshire would too.

Any carb will need to be jetted and tuned. You just need to decide where the majority of your wheeling is going to take place....and set it up accordingly. First and foremost pick up a Weber jet kit (usually under 45 bucks from all the majors..summit etc). Well actually first decide which carb you have!!! The 32/36 will have an obvious difference inthe size of the hole in each carb bore. The 38/38 has identical bore size.
If I can jet a 38/38 to run right up here in flag...you should have no problems in the valley! Also the Weber tuning manual ( amazon etc) is a must. Wayyyyyy too much info for me to convey on tuning. Usually can be had for 10 bucks used.

I personally have found that the 4.2 has a serious compromise. If you run a 31" or smaller, you can get good milage because the they are alot lighter than any 33 inch tire.. With 33"s...it really cant be done, The engine dosent have enough rotational inertia (power/torque) to maintain a tire that heavy at a good speed( ie 2300-2700 RPM) I was running 4.10's with 33" TSL's. I could not get above 10 MPG...and 5th was useless...4th was too.... unless the road was deal level. On the other hand my CJ7 had a 360, 727 auto and 4.10's.....I got about 12-15on the highway...not bad for a v-8 and no overdrive!. The 360 has a higher rotational inertia and more torque!

Just my $.02...but as a daily driver...a 31 should be good enough to get you where you need to go....affordablely. Put a little more money into skidplates/lockers/winch (which you can do over time...unlike when you spin an axle in your M20 and have to pay to have it replaced...then 2 months later you have to pay again to have your new gears installed!)and you wont have to upgrade axels/brakes etc with a 31...with 33's and rock crawling...its a ticking time bomb...and have a more bulletproof rig.
Keep an eye out for a 4cyl CJ being parted out....should be atleast 3.54 gears....maybe even 4.10's. you can get a used axle set much cheaper that setting up new gears...and with a 31 inch...no further upgrade needed! Thats over 1000 saved that you can spend on other toys!!

The stock brakes are basicly worthless with a 33 also. I have installed disk brake kits on all of my CJ's since the late 90's. TSM makes a nice kit. And with the 31's....I can out brake my Grand Cherokee which has ABS! With 33's...it is close to the braking performance of a stock CJ with 235/75/15's.

OK I am off my soap box now.

As far as the head...havent done one yet....seriously considering it though!

I am just trying to steer you away from all the pitfalls I have experienced in 20+ years of playing with CJ's!!
 
Last edited:
as far as gears....look at this...let me know what you find....

amc20cogif-1.jpg
 
Hey Richard,

I actually did something similar with a guy who was rebuilding a Jeep out in my back garage.

It was a 4.0lHO head on a Renix block, but we used the intake from a 258 and his existing EMPI webber style DGEV carb.

It worked out well. I think that the HO head gives a littl ebetter in the breathing department. If you want to keep costs down then the Howell style injection works pretty well. Great for off camber running. Basically you still have wet runners so rich on 3/4 and lean on 1/6 are still issues.

If you can get it with a Full MPI intake and 91-95 computer it is usually the best deal.

You are an old hot rodder so the 4 barrel would be OK. But you know any great angle is going to cause problems.

I got parts for most any of those conversion if you want.

Even got an extra Howell computer and parts if you are interested.

Biggest thing with putting a 258 intake on a 4.0 head will be modifying to fit on top of the alignment pins and then creating special shaped washers for the intake. I was going to get Graoundpounder fab to cut me some of them. If you want I can get him to make up 2 sets.


Carl
 
Currently mine has a bone stock 258 with HEI. I swapped out the stock T4 for a custom built T5 (all the upgrades possible for the Jeep T5 professionally installed to come as close aspossible to WC T5) to have OD and got rid of the crappy stock axles with 2.72 gearing. Swapped in FSJ Dana 44's front and back with 4.10 gears (picked for 33" tires) and run 35" x12.50 BFG AT's. With the stock engine it will run 70 mph on flat ground but does not like strong head winds. I think it is more a function of the crappy stock carb than anything else, I know several guys who have Jeeps with 258/4.0 head setups and they run like a V8.

They are all carb setups so my question about EFI with the 258/4.0 head combo still stands...

I think no matter what you do....overdrive will always be useless. Unless you go mopar EFI on the 4.0 head and add a turbo or supercharger. But then MPG goes down the toilet!!
 
Hey Richard,

I actually did something similar with a guy who was rebuilding a Jeep out in my back garage.

It was a 4.0lHO head on a Renix block, but we used the intake from a 258 and his existing EMPI webber style DGEV carb.

It worked out well. I think that the HO head gives a littl ebetter in the breathing department. If you want to keep costs down then the Howell style injection works pretty well. Great for off camber running. Basically you still have wet runners so rich on 3/4 and lean on 1/6 are still issues.

If you can get it with a Full MPI intake and 91-95 computer it is usually the best deal.

You are an old hot rodder so the 4 barrel would be OK. But you know any great angle is going to cause problems.

I got parts for most any of those conversion if you want.

Even got an extra Howell computer and parts if you are interested.

Biggest thing with putting a 258 intake on a 4.0 head will be modifying to fit on top of the alignment pins and then creating special shaped washers for the intake. I was going to get Graoundpounder fab to cut me some of them. If you want I can get him to make up 2 sets.


Carl

Hey Carl, should have known you had all the parts! :bow: I will give you a call and talk about this. This setup is for my Scrambler so angle issues are not a problem (beach, not trail vehicle). I don't drive the Scrambler to Nags Head right now because I am not sure the old engine is up to it and don't want to leave it on the side of the road. Ted's "Exhibit" has a 258/4.0 head setup with Holley 4 barrel (3.73/T176/33" tires) and it is a screamer! I have a "spare" 258 in the garage and was considering having it built and then swap it in.

I have the built 401 stashed under the workbench but that is way too much engine for my Scrambler! Still trying to work out the SD33 setup but have been unable to find an adapter to put a 5 or 6 speed behind it (NV4500 is not the way to go with SD33).

Richard
 
Ted had that nv3550, which has the same bolt pattern as an AX-15. There was a guy who swapped a Cummins 3.3 into a Yj and he used the AX-15 behind it.

So there is someone out there that makes a round to that style of bell housing converter.

Search for 3.3 diesel in a YJ.

Just shoot me a note or call when you want to get together.


Carl
 
I thought I read somewhere that parts of the 4L head had to be dry-decked to seal off some water passages that don't match the block? Is that accurate?
 
I thought I read somewhere that parts of the 4L head had to be dry-decked to seal off some water passages that don't match the block? Is that accurate?

Yes, you are correct. There are a couple of ways to do it.

The easiest and cheapest is to first pack the selected (not all) water jackets in the head with DISSOLVABLE packing peanuts. Then fill with QuickSteel. Make sure everything is thorougly degreased and thoroughly dry beforehand. Also make sure the quick steel doesn't protrude and the deck face doesn't get contaminated with QuickSteel.

It sounds more radical and difficult than it really is.

The hardest part (which really isn't hard either) of the 4.0HO head swap is torquing the head. Make sure you torque the 4.0HO head to 258 torque specs. 258 torque specs are much lower... the 258 block can't handle the 4.0block specs. Also note the even lower torque specs on the very leading and very trailing head bolts... the block is weaker there.
 
I used JB weld for my 4.0L head. worked great!
 
I have been squirreling parts away for some time to do a 4.0 head swap on a 258 for my Scrambler. I have a complete 258 and was considering having it professionally built with the 4.0 head but am torn between a 4 barrel intake setup, Webber or going with a Howell EFI kit. I know people have put the Howell kit on their stock 4.2's but what about a built up engine with the 4.0 head? I would prefer not the drop a 360 into my Scrambler (I think the power of the 258/4.0 head setup is almost as good as a V8) and the 6 cylinder should be a little better on fuel economy.

Has anyone does this? How is the gas mileage? Other comments? I will be running a 4.10 gears, manual OD (T5 or AX15) and 35" BFG tires.

:cheers:

Richard

Richard,
There is a shop near me in NoVa called High Tech 4x4. One of the mechs there has a 85 cj7 with the 4.0 head and the mopar EFI. I don't remember what gas mileage he said he is getting, but I can tell you without a doubt that Kurts jeep out powers my 4.2 with a Hesco TBI setup. We're both running 4.10's and 33's. Both of us are running 5 speeds (he has a T5, I have a NV4500) and in both cases, 5 gear is actually plenty usefull.

If MPG is really something you need to know about, I'll ask Kurt on monday what he gets.
 
Richard,
There is a shop near me in NoVa called High Tech 4x4. One of the mechs there has a 85 cj7 with the 4.0 head and the mopar EFI. I don't remember what gas mileage he said he is getting, but I can tell you without a doubt that Kurts jeep out powers my 4.2 with a Hesco TBI setup. We're both running 4.10's and 33's. Both of us are running 5 speeds (he has a T5, I have a NV4500) and in both cases, 5 gear is actually plenty usefull.

If MPG is really something you need to know about, I'll ask Kurt on monday what he gets.

Would like to know what he used for efi afterfter the 4.0 head swap. i want to put fuel injection on my engine when i build it with the 4.0 head.

Richard
 
4.0l head swap

I did the engine modification that you want to do. Its awesome you"ll love it. On mine, I had the engine overhaued and bored .060 over with a mild RV cam, added a 4.0l oh head. I added the Howell FI kit along with an HEI dist. and a cold air intake system. including a banks header, I do run 4.10 gears no problem on the highway, I do have the 904 auto trans. This set up runs great, 4wheeling in the Colorado mountains does not skip a beat on off camber or up at altitudes 12,000 -13,000 feet.
 
Back
Top