• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Axle Bearing Race Pitting - is this too much?

hefavitzen

Scrambler Junkie
BENEFACTOR
Gold Member
Lifetime Member
City
Rock Hill
State
SC
New Guy to Axles Alert!!!! I've never taken a set apart before and I'm not having very good feelings about these parts.

Hey guys, I bought a set of wide track axles a few years ago and finally dug in as I am prepping to regear them. But, upon taking the front axle apart I'm a bit worried about the actual axle shafts. First, the rear axle is in great shape. The front axle, as a whole, looks like it may have lived a number of years covered in grease at the bottom of a pond.

So, after degreasing and then de-scaling the axle shafts, they look like this. And, what I would appreciate your feedback on, is if in your experience, is there too much pitting and damage to the bearing races on both the axle shafts and the hubs. I feel like bearings and races should be free of any sort of contaminant, pitting, rough surfaces, etc... and I am probably deep in denial. I figure I probably should buy new axle shafts and hubs but I'd love a second, third or tenth opinion.

Also, is this weld here, where the yolk is joined to the shaft normal? It looks like garbage, but maybe that is what they all look like?
20210330_174531.jpg20210330_174541.jpg20210330_174705.jpg20210330_174759.jpg20210330_174808.jpg20210330_174712.jpg
 
The spindles look usable to me, because the wheel bearings have inner races that fit over the pitted areas.

The axle shafts would be a no-go for me though, because there are needle bearings that ride directly on the pitted areas right behind the yokes.
 
Metalshaper on YouTube 'jeep cj dana 30 rebuild' is an excellent video to get you going. He breaks the process down into bite size pieces. And it is based on a late CJ model. His other vids are equally good as well.
The metal seal that goes on the axle and spindle shaft yoke ends can be replaced. Cold chisel or grinder will remove them. Just need to be aware that the short shaft has a rubber seal that fits into/onto the metal seal...hard to remember. Someone else can chime in here.. You should have encountered it on disassembly. I re-used the rubber on mine so not sure of availability. Outer shaft axle. The pitting looks pretty bad; but they can be replaced. Ebay item used or order new.
 
The spindles look usable to me, because the wheel bearings have inner races that fit over the pitted areas.

The axle shafts would be a no-go for me though, because there are needle bearings that ride directly on the pitted areas right behind the yokes.
What he said 100%
 
Also a note on the spindle damage... That's hammer blow marks. Remember to use a rubber mallet or deadblow to knock the spindles loose. Or an old hot rodders trick, use a magazine wrapped around the spindle if you only have a steel hammer....assuming you don't read your rags on a Kindle.
 
Metalshaper on YouTube 'jeep cj dana 30 rebuild' is an excellent video to get you going. He breaks the process down into bite size pieces. And it is based on a late CJ model. His other vids are equally good as well.
The metal seal that goes on the axle and spindle shaft yoke ends can be replaced. Cold chisel or grinder will remove them. Just need to be aware that the short shaft has a rubber seal that fits into/onto the metal seal...hard to remember. Someone else can chime in here.. You should have encountered it on disassembly. I re-used the rubber on mine so not sure of availability. Outer shaft axle. The pitting looks pretty bad; but they can be replaced. Ebay item used or order new.
Yes! That was an awesome video! Thanks!
 
The advice above is spot on.

That said, the stubs could be ran if needed or as a backup set. You can smooth the pitting with emery cloth. That surface rides on needle bearings in the spindle but will only turn when hubs are locked in or in 4wd. This isn't a long term suggestion and I would plan on replacing in the future. If you do run them change out the spindle bearing when you get new stubs as well since the pitting will probably damage the bearing.
 
Back
Top