• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

best trans for 151 iron duke

craveman85

CJ-8 Member
City
Dolgeville
State
ny
Well I'm attempting to revive my rebuild on my scrambler again. It has the iron duke/sr4/30. What trannies could I directly swap with or what would be easiest. Not looking to swap engines or use adapters if I really don't need to.
 
The Jeep T5 is the best manual trans. It is bolt in in place of the 4 speed.
 
Am I correct in assuming all their 4 banger trannies had the same input shaft?

I do know that the 4 banger input is different. I have a t5 from a 4 banger here and it is way different on the spline count. Google jeep CJ tranny guide there is a great guide out there on the web.
 
I see you are in NY just haven't checked how far. I Read your motor post I might have a four-cylinder and a good trans for u here if you go that route.
 
Last edited:
Jersey is the 4 banger an iron duke or the 150 AMC? My motor is damaged beyond repair (someone put 1/4" sockets in my spark plug holes...) I'd prefer to keep an iron duke in it.most of the info I find is swaps for 6 or 8 cyl stuff and barely any quad-squirrel powerplants.
 
Is there any way to fit a 6 cyl transmission. To a 4 cyl at all? I'm not too familiar with transmission tech because I haven't had to fix any yet.
 
Well.. Maybe. Jim tells us the shaft pilot is same so that is good.
You could search and see if someone makes a clutch disk with the correct spline count and diameter hub to match your input shaft, and has correct OD to fit in your pressure plate. Don't forget to check hub offset measurements too, a disk looks flat at a glance but they are usually offset front to back sides. This would make the hub rub on flywheel bolt heads or release bearing edges, or some other spot.

Out of curiosity, why go back with another 4cyl?
 
my 81 8 came with 258 & T176 trans I found a recent remanufactured Iron duke used the Bell from it mated to the T176 no problem. Only had to drill & two holes for trans housing bolts,
 
Ill check on my motor later today. And ditto on splines Jim good info that's it. I was once excited to get a really clean low mileage t5 only to find out splines were 4 too many.
 
I have 10 splines on both the sr 4 and the t5 with the iron duke.
 
I have no real need for a 6 or 8 cylinder. I plan a regear and 235/85r16 tires with a 2" lift. Offroading in my area consists of mud and I don't like off roading in mud. I also kinda like 4 Cylinder jeeps. Probably the only swap I'd be interested in would be a ford 300 I6.
 
I did find an iron duke that was rebuilt about 1100 miles ago that was converted to TBI and comes with the ecm and harness for 550$ now just trying to fight the ford 300-6 urge again.
 
Finally had a chance to see what I had. The trans is a t4. I have the t5 I talked about as well.

ImageUploadedByTapatalk1418475109.017308.jpg
 
May be interested in one of the trannies. However a t18 may find itself in my garage later this week. If it does then a reman 300 ford i6 will be being rebuilt shortly after. Do you feel like 5th gear would be useable in a 4cyl cj? A little off topic but I require pictures or links to pictures of your j20's the 300 dually and... The 715
 
While the 300 is a great engine, check out the weight of it compared to other options. From what I remember, it's a very heavy and long engine.
 
Back
Top