• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Factory fogs - need wiring help please

AdamH

Scrambler Junkie
BENEFACTOR
Gold Member
Lifetime Member
SOA Member
City
Surf City
State
NC
Fog lights - I have the original lights and the switch that attaches to the dash. That's it. the relay/fuse/whatever isn't there. What size relay/fuse was used? I will need to build the harness from the switch to the lights themselves. I do have the plug still attached to the back of the switch with 2 red wires and a black wire coming out of it.

thanks
 
In OEM form:
The switch pulls power from the dimmer switch circuit on the grey wire, so it can only work when low beams are on.
The red/trace goes to ground and one side of relay coil. I know its weird, but that is what diagram says.
Dark blue is switched and goes to other side of relay coil.
The relay pulls power for the lights from fuse block on the parking/tail light fuse.

934106d1387679443t-oem-fog-light-wiring-diagram-drivinglightschematic.jpg

Mine has a 20 amp fuse for park/tail and matching relay...
 
Oh.. and all these plugs/connectors should exist in all 82 and up harnesses if they weren't hacked out at some point. Not sure about 81 and earlier...
 
I have the painless wiring in it now. I purchased a factory under dash harness from Jersey including the fog light harness side. I also have a FSM. Since I am able to identify (both with your help above as well as my FSM) the 4 wires from the harness all I need to do is splice them into the Painless set-up.

1st is white = need to know where to splice
2nd is black = ground
3rd is orange = ends up at fog light but need to know where to splice
4th is gray = low beam but need to know where to splice

The Painless system pretends fog lights never existed
 
1st is white = need to know where to splice - This is the power feed that goes into the relay to power the lights when relay is triggered. In stock form, it was spliced into the parking/tail light circuit (after the fuse so it is protected along with parking/tail harness)
2nd is black = ground
3rd is orange = ends up at fog light but need to know where to splice - In stock form this is the power from the relay to the lights. The wire turned from Orange to Red as it passed through the firewall plug, ran out to the grill shell and then split to the left/right lights.
4th is gray = low beam but need to know where to splice - This wire splices to the solid grey lead on your floor mount dimmer switch harness. It controls power to the switch so that the switch can only close the relay when low beams are on. To have switch activate relay for fog lights in both low and high beam positions, splice or jumper this wire to both the grey and grey with trace leads on your dimmer switch harness.
 
Fog lights - I have the original lights and the switch that attaches to the dash. That's it. the relay/fuse/whatever isn't there. What size relay/fuse was used? I will need to build the harness from the switch to the lights themselves. I do have the plug still attached to the back of the switch with 2 red wires and a black wire coming out of it.

thanks

I sent you a PM.
 
1st is white = need to know where to splice - This is the power feed that goes into the relay to power the lights when relay is triggered. In stock form, it was spliced into the parking/tail light circuit (after the fuse so it is protected along with parking/tail harness)
2nd is black = ground
3rd is orange = ends up at fog light but need to know where to splice - In stock form this is the power from the relay to the lights. The wire turned from Orange to Red as it passed through the firewall plug, ran out to the grill shell and then split to the left/right lights.
4th is gray = low beam but need to know where to splice - This wire splices to the solid grey lead on your floor mount dimmer switch harness. It controls power to the switch so that the switch can only close the relay when low beams are on. To have switch activate relay for fog lights in both low and high beam positions, splice or jumper this wire to both the grey and grey with trace leads on your dimmer switch harness.

thanks for this! I'll try and get to this sometime this week.
 
Back
Top