• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Factory V-8 tach with Edelbrock MPFI AMC 401

red mistress

Red Jeep Collector
City
Piney woods
State
tx
http://i226.photobucket.com/albums/dd178/RedScrambler/DSC00258-1.jpg

http://i226.photobucket.com/albums/dd178/RedScrambler/DSC00458.jpg

http://i226.photobucket.com/albums/dd178/RedScrambler/DSC00246.jpg


I've heard that the factory tachometer will not work with the Edelbrock Fuel injections system?

I'm also running the DUI HEI distributor.

Putting an old school tach on my 67 Gladiator and it has a "box" that sends signals to the tach. So it got me thinking about getting rid of the el-cheapo aftermarket tach in Scrambler and using the NOS V-8 tach I have.

I know this is a very hard question, but I figured someone here has made it work?

Some engine pics so you'll know I'm not B.S. n'. :rolleyes:
 
Good luck with the Pro-Flow injection. With the tach, you could use a current triggered MSD Tach adapter to get the factory tach to work.
 
Current triggered

Current triggered adaptor, That must be the "box" for the old timey tach I've got.


Yea, the Pro-Flow was a real pain getting it to run half way right.
Finallyt ook it to "tuners" with rear wheel chassis dyno.

The 401 engine dyno 480 with carb.
Chassis is only 220:mad:

But it does start right up easy.

Is there a "better fuel management system"?
I do need to change that out as fixing to have to pull motor accessories apart to adjust valve lash.
 
I couldn't get a stock tach to work with my Howell TBI injection and a DUI distributor. I ended up getting one of the newer reproduction stock looking tachs. It hooked to the tach lead in the Howell harness and worked. Those are adjustable for 4-6-8 cylinders too.
 
Repro

Hey John,
Been enjoying the Garnet items you parted with.
No "collector" nut has ever seen Garnet half doors.


The reproduction 4-6-8 is the Tach i have in there now.
No comparision to quality of the origional.
 
mpfi...tach

HEY, I've got that after market tach like john has w/the switch for 4-6-8 cyl and a 383 v8 chevy and the tach works fine. can't say that much for the edelbrock mpfi other than it s_ _ ks. If i had it to do over i would go w/the howell fi for sure.. I had it on a amc v8 and loved it. Although i would have to agree w/ Red Mistress on the edelbrock mpfi it does start easy but you just can't seem to get it tuned for anything... oh well...
 
The Howell still has the same issue as the Pro-Flow....It requires a chip to be burned.
 
mysunnshine said:
The Howell still has the same issue as the Pro-Flow....It requires a chip to be burned.
The chip that came with mine has worked just fine.
 
As long as you have a "stock" motor or a really mild performance motor, they work alright. I have yet to see one that the fueling is good and would not need any changes. I guess it's kinda like this. What you don't know will not hurt ya. Will you really know that it runs at 13.8:1 at WOT or 12.5:1 at idle in gear? They both "feel" good when you're driving. You just can't see the headers glowing red as you're pulling that long hill.
 
Mpfi

I know the chassis dyno shows the parasiteic (sp) from tranny, T/C, axles and turning 38" tires.

I've only had the 401 installed in Scrambler with the Pro Flow = 220 HP to rear wheels is OK but not fun in sand dunes / mud when you just wanna hear it roar.

Pro Flow also doesn't have fast throttle response until motor is reved to 1500.
It always smells rich which brings tears to the eyes.

I was in the dyno control area with the Carb on motor when it pulled best 480 @ 4100.

The import tuners were telling me I needed a programmable FI management system. I really didn't speak their language.:confused:
 
The Red Mistress 401 Scrambler

Hey I Rode In The Red Mistress Scrambler And It's Go A Lot Of Hp. Seemed Fine To Me.. Enough To Make Me Hang On.........


The Braking G Force Equals The Foot-to-the-floor G Force. Lol Lol Lol Lol...... Most Impressive Truck All Around....

The Reproduction Tachs Are No Where Near The Same Quality As The Oem. You Can Reprogram The Oem 4 And 6 Cyl Tach To Work On V8.
 
Hp

Thanks Joe,

But never enough HP espicially since I know there is alot more!

Since Bulltear is going to make the serpentine belt system for AMC V-8's I might as well aluminum heads, shorty headers, and the FAST FI system while I'm in there.
 
Back
Top