• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Figuring out my stumble

Doc Savage

Basic User
City
Greenville
State
TX
Ok not really sure how to describe this other than a stumble. Occassionally at highway speeds I almost think the motor misses, but where I know something is wrong is after running for awhile (good and warm), and I either hit a stop light, or get home and just let it keep running, it will start missing a bit and the rpms drop. If I give it some gas, it will take a few seconds and then smooth out. It will idle normally after that.

I've read of some jet issues doing something similar, but I don't think it is quite the same. In the threads I've see on the dirty jet threads, they say to look down the carb throat and you should see gas dripping. I don't see anything like that. Everything looks fine.

Now here is some info that I think is important. I'll admit that I don't know exactly what I have, but I know it isn't stock now. The previous owner had eliminated the computer and stepper motors on the carb. I'm missing a bunch of stuff under the hood and have tons of "spare" connectors and disconnected sensors. There is no choke, the previous owner did have a manual choke added with a cable. The cable had frozen and today I got around to putting a new on today, but don't think that would impact it after it is warm. The jeep as it didn't have a choke, was not the best to drive in the cold before. You really had to let it warm up before going anywhere. Here are some pics of the carb.

20131026_105759_zpsgkhczozs-1.jpg


20131026_105811_zpsqc168rtx-1.jpg


Here is a video of the motor running rough (I was in the cab so showed the tach)

http://vid57.photobucket.com/albums/g201/DocJeep/RCRC%20sale/Scrambler/20151016_210711_zpsbps1p8vu.mp4

Here is a video of the motor running after running into town today. She is real hit or miss with the stumble.

http://vid57.photobucket.com/albums/g201/DocJeep/RCRC%20sale/Scrambler/20151016_210711_zpsbps1p8vu.mp4

I've been running carb cleaner in the gas when I've added gas, and I tried hitting all the orifices I could see in the carb with spray cleaner. When we rebuilt the motor, I didn't do anything to the carb but pull it off and then bolt it back on. I didn't want to change any adjustments or anything, so I held off rebuilding it. Not sure if that should be done or not.

Any thoughts as to what is going on or what my next steps should be.
 
Have you given the jeep a good tune up. How are the plugs and wires. Going in another direction, how is the gas and fuel tank. Acting like you got bad gas. If the fuel tank has crud or rust in it, it could play get in the carb and give you a world of problems (especially if it's floating in the fuel bowl and intermittently blocks the fuel passage ways).
 
1. All the fuel cleaner in the world won't clean out a really bad tank.
2. Had this problem on my 20 yr old Hummer H1. Ethanol fuel tends to loosen up an clean varnish in older tanks that may have used only 100% gas for so long. Guess where all this gunk ends up. I was changing the fuel filter every week until I just replaced the gas tank. My Hummer is a Gas engine. I'm corrently rebuilding my 83 Scrambler and I just threw the old tank away and bought a new one.
 
You are effectively running out of gas. When you give the throttle a bump you are increasing rpm, which increases rpm to the fuel pump lever, which increases fuel pressure. The increased fuel pressure dumps more fuel in the bowl and gives you a little run time until the cycle starts again. A fuel pressure gauge T'd in would be a good place to start. If you are lacking tooling and gauges then it's going to become a best guess parts change/repair fix. I would start by removing the carb and checking cleanliness. Check the float height, needle and seat for cleanliness. While in there a can of carb cleaner wouldn't hurt. So at the minimum you'll need a carb rebuild kit. From there I would change out the fuel pump and get back to us.
 
Well been trying to narrow things down some. I hit the carb with spray cleaner concentrating on the idle ports. Sunday the jeep ran real well. I had also installed the manual choke that had been missing. It ran great Sunday. I took it to church and made a few stops along the way back home and never had an issue. The choke worked pretty good also. Monday it started well and ran good in to work (traffic was awful and took 50 minutes instead of 30ish like it should). Gate traffic at the arsenal was bad, 15 minute delay getting thru the gate. About halfway thru the wait, it started acting up again. I was able to engage the choke to bump up the rpm and that helped some, but it was rough on the takeoff after the gate, but smoothed out after a bit. I took it out at lunch and was still a bit rough. Looking at the idle screws, I adjusted the idle up some to where it was idling about 800 rpm with it warm.

I did some reading this afternoon, and looking at it, I think alot of the issues come from the fact that the previous owner had removed the carb electronic and smog stuff, and nothing operates like it should. Having no choke other than the manual choke is where I think I may have the most issues. Essentially there is no curb idle vs fast idle adjustment unless you manually operate the choke. I think it will take a bit of time to get it straight and set right.

I don't think crud in the tank is the issue. It is a poly tank and we cleaned it out while it was out. I did reuse the hardline to the fuel pump, and that could have had junk in it. I've swapped in a new fuel filter after we got it running so I'm not too worried about crud getting to the carb.

I may need to break down and clean the idle jets like has been recommended alot online, but I'm not seeing gas drip like should be happening if that was the case.

I think figuring out how to operate the carb without any of the automatic controls is going to be the real issue. I'll post pics of the carb and choke after I get them downloaded.
 
Drove in ok this morning, but acted like it wanted to keep running when I stopped. Smelled a bit rich, so after driving home, I tried adjusting the mixture. Ended up going in 1 3/4 turns on both screws. I should have run them in to see where I started from, but didn't expect alot of adjustment was needed. That could explain the 12 mpg on the last tank also.
 
Back
Top