• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Fully Custom Cj8 Build

Cody: I can relate to your desire to own a vehicle built completely to your spec. I have personally answered this question for many people. But,,,Building a Jeep from scratch is a very long and expensive project. There is a lot more to it than meets the eye at first glance.:)

I should know I've been working on mine for the last 4 years on the actual build, and 8 years total designing and procuring parts. $25K will get you started but it is far from the end of it, especially if you are going to buy all of the parts outright, and do a first cabin job.

$25K will get you the frame, body, axles and maybe most of the drivetrain. Thats about 1/3 of the complete vehicle. You can plan on spending at least another $25K to finish it out.

Look:
TDC Frame $2K
Aqualu Body $4K
Dynatrac Axles $8-10k
Suspension of choice $3K
Chevy Engine $3K
700R4Trans $1K
Atlas $3K
Wheels and tires $2K

total so far $26K Then there is about 500 little piece parts that range from $10 to $1000 you need to complete the project. :eek: There are obviously ways to cut back on these prices but full pop, this is what you're looking at.

Plus figure several years of keeping the project funded and moving forward and keeping your head in the game. Even if you had enough money to buy every part tomarrow it woul still take you a year to assemble everything correctly and get it wired plumbed and running right.

I fabbed a large portion of my Jeep including the frame complete undercarriage, all of the adapters (they didn't exist before) all of the body and Rollbar mounts, and virtually everything made of steel or aluminum.

I am well over $25K and still have to buy three major pieces to buy. A/C system ,top, and fuel tank.

Mine has a 4BT Cummins motor a TH400 US Gear OD and Atlas , which when geared right will yeild between 25-28 MPG. However I had to "build" this drive train, the adapters are not available commercially.

If you are still planning the Ford Diesel, I would recommend forgeting the idea. :banghead: It's just physically too big for a Jeep. Also there is very little you can do to make any Jeep tow a 22' boat well. They are just to light and too short to tow anything bigger than a small tagalong trailer very well. In other words the vehicle can't control the trailer so the trailer ends up controlling the Jeep. Not good when you have to panic stop or change lanes in a hurry. WOOHOO!!!!!!!!! :rotfl:

The Chevy drivetrain mentioned above works well and won't break the bank, just a TBI 350, 700R4 and Atlas would be a good drive train. D60 and D44 axles or D60/D60.

If you really want to see what it takes to build one from scratch checkout my build at www.4BTswaps .com "Here's the DeScrambler" :thumbsup:

Think long and hard before you jump off this cliff, It's a long way to the bottom and it costs a bunch to get in the door. I'm 60 years old ! I've been working on mine since I was 52!

That's not to say you can't do it. In fact, I encourage you to do it!!! What I'm saying is you need to do YOUR homework ,and plan the project from beginning to end many times in your head before you start.

Here's a big consideration: Everyone around you must be solidly on board with your project. Finding out you can't afford to finish the project when you are half way thru it, or that your wife is going to bail when she sees how much you're spending and threatens Divorce, just means you get to sell everything for 10 cents on the dollar. :angry:

That is just the nature of a custom built project. It's what you think you want, not necessarily what anyone else wants. :evil:

The exact Jeep you want to make was built about 6 years ago by my friend Danny Grimes for Dave Knight who was the guy who sold the Aluminum bodys before Aqualu dumped him. It cost right at $50K to build and has a LS6 engine with 4L60E trans, atlas D60/D60. It was built specifically to run the Ultimate Adventure in the Carolinas around 2004-5. Also there was much "sponsorship" involved" that actually kept the cost down to $50K. And since the previous owner couldn't pay the bill it now is owned by Danny Grimes and resides in Moab UT. None of this stuff is cheap, don't step up if you can't compete, you'll just get ruined in the process. :D

Randy
 
Last edited:
Good luck with the build... it is an ambitious one... the time table is what I think is in the right range... it is the cash valuie that might go higher depending on the motor you put in there and what it will take to get it in there and going.

It is always 2x the money and 3x the time for some reason!

cb

I just looked at some of my non-diesel build ups and the prices with me doing all the work... well over$25K to get them up and going.

My advice to you would be to buy a couple of CJ's for "parts jeeps" for all the little pieces... unless you want it new, that stuff really nickels and dimes ya.

cb
 
Ok Codyaku here's what you need to do. Go help W.R. Buchanon finish his jeep build which should be done just about time he is ready to retire so he will need to sell it for 50 cents on the dollar to fund his retirerment. However at the half price it will still be more than your 25k budget, but maybe he will let you make payments for a minimual intrest rate!!!!!!!!!!!!!!!!!! ( just had to have a little fun after reading all this)
 
www.4BTswaps[/url] .com "Here's the DeScrambler" :thumbsup:

Think long and hard before you jump off this cliff, It's a long way to the bottom and it costs a bunch to get in the door. I'm 60 years old ! I've been working on mine since I was 52!


Randy

Randy has great insight here, and even though I only quoted part of his post every single bit of it is true. I could buy a new Unlimited for what I have into mine, and that's not even counting my labor! Not to mention I have at least 3 years on my build... buying an unfinished project is really a $ saver.
 
njrcj8: you are a vicious individual, I should be able to get 60 cents on the dollar, plus that I'll never be able to retire, de Bamas needs me to work ta pay de meskins for livin' here!:crazy:

Nope guys if you're planning on selling it you might want to buy BP stock instead it'll be worth more after they're bankrupt and come back. :banghead:

The only reason to do this stuff is to use it, and use it for along time, to get your money out in use. Otherwise you're better off buying a stocker and just driving it, at least It'll be in the BlueBook. There is no Kelly Blue Book for Custom stuff.:rotfl:

Watch "Pawn Stars" on the History Channel. You'll get the idea in a few episodes.

It's never worth what you think its worth, it's only worth what the man with the cash is willing to give you for it. Rude Awakening? Reality is a *****. :evil:

Randy
 
thanks alot for the help. im trying to make this as budget friendly as possible. I, gonna tone it down alot and look around for a scrambler that i can build off of. where can i find a turn key vortec motor?
 
There's usually some on EBay. I'd suggest checking with your local wrecking yard, sometimes you get lucky and get a hold of someone who thinks your project sounds cool, and they give you a good deal. Be specific that you need everything.
 
If you want to keep it simple and reliable consider a 4.0l fuel injected motor. I see them routinely complete for $300 or so. I've done the late model chevy v8 swap and I love it but there is a lot that goes into it to get it right. There is a ton of info out there on the 4.0l swaps. Like everyone is saying you need to do your research and decide what is best for you.
 
for 25K, and given the best bang for buck, I'd find a good LJ with slight front end damage and swap over the CJ cowl/hood/fenders/and grill. You'd have the look of a long Jeep with the classic style of a CJ. MPFI engine, coils, and all the small stuff a COMPLETE Jeep has. Throw in a long arm kit, armor, axles, tires, lockers, etc, and be many thousands and about 1 year ahead of the plan....Then buy a used F250 to tow it to far away events....and call it done.
 
can the cummings 4bt tow a 2800lb boat no problem? i think the horse power on those things are like 150 right and torque is like 350 ftlb torque.

the 4bt can pull it im sure, they pull big bread trucks dont they? also the 4bt is a low rpm engine. to go on the highway with 456's might be too much even with a .75 final ratio

but remember!!!!! the cj-7 is rated [ i think ] at 2K lbs towing and at that weight i've read they are scary to drive even dangerous . who knows what long arms, lift, etc. is going to do.
 
Just another LSU fan here.
But I would be scared to pull anything to heavy with such a short wheel base too.
 
Back
Top