• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

My De-Rustification Project

Probably has to go ground shipping. Eastwood is only 15 minutes from my job, Quadratec 35 minutes, extreme terrain 25 minutes:D
Used some on a trailer at work, seems to be holding up good. Also available in quarts.

Seems like I could just pop up and pick some up myself. I did not know that Eastwood was in PA.
 
You might want to consider adding a crossmember /trans brace toward the center of the frame to keep the sides from bowing out making your shackles crooked.

I'm getting a replacement (factory) frame next week and plan to do this. Good luck and eager to watch yours go together.
 
You might want to consider adding a crossmember /trans brace toward the center of the frame to keep the sides from bowing out making your shackles crooked.

I'm getting a replacement (factory) frame next week and plan to do this. Good luck and eager to watch yours go together.

If you have pics of where to put it so it won't be in the way of stuff, that would be appreciated.


By the way, I have been fighting a intermittent issue with my e-fans not working, so I have not been doing much to the frame. Well, I found the bad connection in the ground to the fans (yes, another ground wire issue). I hope to have some time this weekend to cut off the rear cross member.

I was looking at the body mounts. It appears that they are not all at the same height with relation to the frame rails. How exact will I need to be when welding the new ones back on? Could I just align the body mounts to the top of the frame rails, or will some have to be slightly higher and some slightly lower as on my donor the way it sits now?
 
So, I have not had the time to actually do anything with the frame yet, but I have started working on the list of things to do. It's a start, right? Well here is what I see as needed to get or needed to do. Please let me know if you see something missing or wrong.

-Cut off the original cross member
-Weld on the new one
-Cut off the body mounts (small ones)
-Weld on the new ones
-Weld top sections of new body mounts to the two existing longer body mounts (the kit of new mounts do not have the two long ones?)
-Drill holes for the tall shock towers (thanks for the template Randy)
-Obtain taller shock towers (optional since I could re-use the current ones)
-Obtain M.O.R.E. motor mounts (again, I could re-use the ones I have)
-Obtain front & rear spring hangers
-Obtain full brake line kit
-Obtain fuel line kit
-Obtain new proportioning valve (should I?)
-Obtain Eastwood Chassis paint (pictured above)
-Paint the inside of the frame
-Primer frame
-Paint frame

THEN GET TO DUSTIN'S TO DO THE SWAP ALREADY!!!!!!! :eek::eek::eek:

So. How does that sound?
 
Swapped out my headlights with these Hella globes with white ipf "fat boy" bulbs. These pics are in the garage but i will see how much better of a light pattern they give the next time I drive at night.

Before
d9355f4f6930783047a7dde23ee9fba1-1.jpg


After
f9ca277411c987b7c8daf55d59a6d4a6-1.jpg
 
What do the globes look like when off?

I almost took a pic of that last night. I will get a pic today. Flatter than the original for sure. And I noticed this morning that I need to align them again. Oh well. I hope people weren't bothered when I drove in this morning.
 
So, I have not had the time to actually do anything with the frame yet, but I have started working on the list of things to do. It's a start, right? Well here is what I see as needed to get or needed to do. Please let me know if you see something missing or wrong.

-Cut off the original cross member
-Weld on the new one
-Cut off the body mounts (small ones)
-Weld on the new ones
-Weld top sections of new body mounts to the two existing longer body mounts (the kit of new mounts do not have the two long ones?)
-Drill holes for the tall shock towers (thanks for the template Randy)
-Obtain taller shock towers (optional since I could re-use the current ones)
-Obtain M.O.R.E. motor mounts (again, I could re-use the ones I have)
-Obtain front & rear spring hangers
-Obtain full brake line kit
-Obtain fuel line kit
-Obtain new proportioning valve (should I?)
-Obtain Eastwood Chassis paint (pictured above)
-Paint the inside of the frame
-Primer frame
-Paint frame

THEN GET TO DUSTIN'S TO DO THE SWAP ALREADY!!!!!!! :eek::eek::eek:

So. How does that sound?

Sounds pretty good to me. [emoji3]




 
If you have the 6 cyl motor I have a set of M.O.R.E engine mounts I can sell you. Bought from another member who had listed as for the amc 8 cyl. When I got they were for the 6 cyl. They were test fitted, but the project was never completed so they are new. Was going to return but it was when my father had a stroke and things were a mess that year. Wasn't right to try to return 8 mths later https://www.cj-8.com/forum/showthread.php?36912-Jeep-stuff-for-sale&highlight=M.O.R.E+MOTOR+MOUNTS. I'll ship them to you for 200.00. The proportioning valve, if it works keep it. New ones have a habit of leaking (aftermarket ones are not as good as your original. Use epoxy primer on the outside of the frame (can be painted on with a brush if you don't have a spray gun). This stuff is incredible, I used it on my truck and then painted black. I didn't put enough paint on so when I wet sanded the paint I sanded through the paint to the epoxy in sections. Since the epoxy was a dark grey and it's a work truck (my season was starting), I was going to repaint the next winter. Never got around to it and that was 3 yrs ago. In Cleveland winters, no rust, peeling. Looks the same as it did 3 yrs ago. Can't beat that.
 
I like the headlights, they still have a fairly stock look.
 
If you have the 6 cyl motor I have a set of M.O.R.E engine mounts I can sell you. Bought from another member who had listed as for the amc 8 cyl. When I got they were for the 6 cyl. They were test fitted, but the project was never completed so they are new. Was going to return but it was when my father had a stroke and things were a mess that year. Wasn't right to try to return 8 mths later https://www.cj-8.com/forum/showthread.php?36912-Jeep-stuff-for-sale&highlight=M.O.R.E+MOTOR+MOUNTS. I'll ship them to you for 200.00. The proportioning valve, if it works keep it. New ones have a habit of leaking (aftermarket ones are not as good as your original. Use epoxy primer on the outside of the frame (can be painted on with a brush if you don't have a spray gun). This stuff is incredible, I used it on my truck and then painted black. I didn't put enough paint on so when I wet sanded the paint I sanded through the paint to the epoxy in sections. Since the epoxy was a dark grey and it's a work truck (my season was starting), I was going to repaint the next winter. Never got around to it and that was 3 yrs ago. In Cleveland winters, no rust, peeling. Looks the same as it did 3 yrs ago. Can't beat that.

I will think about it. That is a lot of coin. I need to do some research.
 
So I drove for the first time in the dark since swapping the lights. I think I need to adjust the aim. What do you think? I did not get a shot of the hi-beams, but wow. It lit up the neighborhood.

f5bb01ee37c7a53dd6d003d4016b7fb3-1.jpg
 
So last night I adjusted my headlights a bit (raised the beam). Seemed better on the drive home at 10:30. And today, I started adding things to my Amazon cart, such as the Eastwood inner frame paint and Eastwood Chassis paint. Hopefully this weekend I can get the rear cross member cut off and see about how to mark the frame mounts so I know where to put the new ones once I cut the old ones off. I really wish that I could weld. But not sure that I want to learn on this project. I want it to be sturdy.
 
So I just removed the old crappy crossmember and test fit the new HD one from Chief Waho

1591f6233c5e3e32952df1a0cbaa025f-1.jpg

bac6cdcf58d4707dd7232d55cb792b63-1.jpg

ff399c39835c963187eac5e30bba6c60-1.jpg


Now I am going to start cutting off the old body mounts. I am not sure how much I have to worry about the exact line up of the new ones. They don't seem to be consistent. Can I just make the tops of the mounts flush with the top of the frame rails?
 
Nice! What are you doing / replacing the body mounts with?
 
Back
Top