• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

one piece axel?

gaducker

Legacy Registered User
City
Newnan
State
ga
So i put one piece axels in when i first got the jeep, have not had a problem till this morning, it seems the taper bearing ate itsself up from the outside in. Now???? Where do i get new bearings and a lock ring? Or is it just a stock bearing ans can i heat the lock ring off nd reuse it?
 
The axle manufacturer can provide you with another and that lock ring is one time use only. the new bearing kit will come with it though. Ive been down this road a coule times.
 
I dont remember what maker it was, I just ordered a single side repair kit and hope its the same, SInce its the same bearing in most I would think the id of the lock ring would be the same as the bearing which would also be the same from axle to axle??? NO??????
 
Generally yes. Some axle manufactures use ball bearings instead of tapered but you said that you already identified it as a taper bearing. Mine are older Moser axles with ball bearings from a company called Green.
 
I got the bearings on and when its tight its hard to turn, not impossible just stiff. I drove it home and that side is warmer than the other. My question is how is preload set? I don't have any shims in it and the block in between the spider gears is still there. I suspect this is what happened to the last bearing that was in there. Any help would be appreciated.
 
Is it a mosser one piece. The may require the thrust block to be removed (not needed with the one piece axles). The axle shaft hits the block and puts pressure on the bearing. If this is you're case you will burn out the bearing. Theirs been other threads on this subject. I had my mechanic install a limited slip when he installed the one piece and new gears so I never had to worry about it. I don't know if this is the same with other manufactures.

Edit:https://www.cj-8.com/forum/showthre...e-install-bearing-drag&highlight=thrust+block There are also others on jeepforum.com that I've read. Hope this helps
 
Last edited:
They were not mosser. I was in the pumpkin last week and the thrust block was not in a bind at all. I may have to buy some shims or grind off a couple thou from the inboard side of the race itself.
 
On the mosser axles they have a spacer that you cut to get your setting (no shims, I asked my mechanic since shims would be easier and he explained that shims are too soft. That the constant load during turning would compress the shims and you would have extra play). If you have the spacer and didn't trim it to the proper thickness when you bolted on the retainer maybe that's putting extra pressure on the bearing.
 
de2epuhy-1.jpg
 
The last ring that goes on the back of the bearing is what you are talking about cutting down??
 
The last ring that goes on the back of the bearing is what you are talking about cutting down??

Yeah that's what you can grind down instead of using shims. The bearings spacer.
I just finished installing a set of 1 piece axles this weekend.


 
Yeah that's what you can grind down instead of using shims. The bearings spacer.
I just finished installing a set of 1 piece axles this weekend.

Justin did you have to gring down the pass side? did you remove the thrust bearing?
 
I installed Moser axles in my green Scrambler awhile back, two quick notes:

1) Install the spacer rings. Then, BEFORE pressing the bearings on the axles, stick the bearings in the ends of the housing. With the spacer rings drove in all the way, make sure you have the requires bearing "stick out". If the spacer ring is in all the way, but the bearing sticks out too far, use a slide hammer and pull the spacers out. Then machine them down.

2) When I went to install the second axle, it would not go in all the way. After scratching me head, I remember the instructions mentioning the "thrust block" inside the diff. On my green Scrambler, that has a Trac Lock, I had to pull out the thrust block.

I installed some Moser's in Jeep Addict's white Jamboree, IIRC, I had to pull out the thrust block, same thing, Trac-Lock.

I don't think I have ever had to machine down the spacers, but if AMC built the housings, we all know how they are about tolerances:rotfl::twocents:
 
My mechanic has installed the mosser axles on two of my jeeps and had to cut down the spacers. On both he installed limited slips so I didn't have the thrust block problem.
 
Back
Top