• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Question on 1982 Scrambler Engine Swap

letsdrag

Basic User
City
billings
State
mo
I have a 1982 scrambler that has been setting for about 10 years. I figure at this point would be easier to just swap motor out instead of getting it running. Has original 4 cyl with 4 speed tranny in it. Was wondering what motors would swap right out, and bolt up to tranny and engine mounts. Can anyone help me out with this.
 
You could do a gm 4.3 v6 or a 305/350 v8. Need 10.5" clutch set and small flywheel (150-something teeth instead of 160-something) to use iron duke bellhousing. Motor mounts are available for either engine
 
For ease of use-- +1 on 4.0 swap or a Mopar FI 258 if you can find one. Also read up on trans/transfer case inputs to be safe.

For fun $$$-- I am a ford guy and I think it is hard to beat a new aluminum LS motor for a motor swap.
 
4.0 is an easy swap for the jeep, but going from 4cyl to 6cyl will require more work then most who go from the 4.2 to the 4.0.
There is vast amount of information out there on the swap. I am in the middle of the 4.0 swap myself. But it is 4.2 to 4.0.
We will help you with information as what ever way you go.
 
Thanks for the replies, I would like to go with V-8 but at the same time I have a older wrangler with a 4.0 in it. So that would be the quickest way to get it going. Would the 4.0 bolt up to the orginal 4-speed tranny, also would I need to move motor mounts.
 
The easiest swap for this is a carbureted Chev V8. The bellhousing is the same, some MORE mounts, a conversion radiator, clutch stuff, and you're in business. Here's the parts list:

Originally Posted by Randyzzz
350 conversion parts list....

--------------------------------------------------------------------------------

Ok...I grabbed my folder of notes...(I wish I was that neat...I copied the numbers off the box labels I stuck on the garage wall)! So...here goes. If you have any q's, let me know. Oh, and to let you know what I started with, it was an 82 GM "Iron Duke" 151 4 cylinder, with a T-176 trans, and a 4" lift.

1. Motor mounts- M.O.R.E
2. Headers- Hedman "Tight Tubes"
3. Radiator- from Tellico 4X4, about $189.95, works fine. (Replaced with a Northern aluminum unit, the Tellico unit didn't hold up. Cost about $250.)
4. Hoses- Napa # 7470 and #7575. Not sure which is for the top or the bottom, I do remember the bottom had to be trimmed at one end.
5. Power steering hoses- I had Napa make up some compression Fitting splices to fit two hoses together. Works great.
6. I used a stock long water pump with a stock fan clutch, stock fan, and a Commando V-8 shroud. (a cj V-8 shroud should work too).
7. The stock bellhousing fit the Chev 350 motor, find an "iron duke" bellhousing for your swap.
8. Use a 153 tooth flywheel, a diaphragm pressure plate Napa CA1897, and a Napa RCF 556 10.5" disc. This is the combo for the T-176. Use the stock 82 T-176 throwout bearing, and keep the stock hydraulic clutch setup. You will need to file one of the slave cylinder mounting bolts to clear the oil filter, you'll see...
9. The trans mount is attached to a plate which cantalievers the mount backwards. Reverse this setup, you will need to drill new holes in the skid, but they will be on a level area. Again, you'll see.
10.The rear driveshaft is ok with a 4" lift. The front is extended a little too long, but I haven't overflexed it to pull out (yet).
11.The GM hei distributor needs a strong 12v power feed, one of the existing wires will work. Also the temp and oil pressure senders on my 350 were compatible with the stock gauges.
12.I got rid of all the other wires...I hate clutter. Oh, and I used the stock "iron duke" starter...and it cranks the 350 with authority. The GM starter has a built in solenoid, so you can loose the external starter relay and associated wiring. Positive cable to the batt terminal on the starter and the "hot in start" wire to the ign terminal on the starter.
13.I used a stock mechanical GM fuel pump, and capped the tank vent hose.
14.For a daily driver manual trans, the T-176 trans is ok...a little slow between shifts, the 350 builds revs fast. I like the T-176 mostly because I cant justify the $$$ for a NV4500.
15.Everything else seemed to fall into place...but every swap is different. Good Luck!
 
Back
Top