• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Soft Springs OME, Pro-comp, Washboards, etc

MomoJeep

Basic User
City
Seattle
State
WA
I have pro-comps springs from over 10 years ago. They seem ok. They have the skid pads between the leafs. Can any say for sure that switching to OME will make a significant difference? My main issue is washboard roads. The vibrations are beating the shit out of poor old Jeep.

Also, is it safe to say the shocks are more important than springs on washboards? I have standard pro-comp shocks. Should I get ones with reservoirs?

Just change shocks, or do the full deal and change springs as well?
 
Softer springs, from OME, Rubicon Express, or BDS will help. I don't have any Jeeps with OME springs, but I do run BDS springs on my green Scrambler, and Rubicon Express on my red Scrambler. I am happy with both brands of springs. Way softer then the Rancho or Superlift springs I have had in the past.

Better shocks will help, too. I run Bilsteins on my red Scrambler, BDS on my green, seem to be good.

BUT, springs and shocks are just one part of it. The biggest/easiest/cheapest improvement for riding on rough gravel/dirt roads - AIR YOUR TIRES DOWN. Air your tires down to like 12-15psi, see if the ride improves.

When we were in Hurricane, Utah, for the National Scrambler a year or so back, I went on one of the "scenic" rides. Basically, miles and miles of gravel/dirt roads that had been partially messed up by recent heavy rain. After about a mile, everyone was airing way down. Biggest ride quality improvement you can make.

People often forget, but your tires/air pressure play a critical/primary role in ride comfort/suspension performance :twocents:
 
I did air down. It was still rough. The washboards are horrible this year (they didn't get any rain). Some of the washboards are 35mph. Sometimes if you drive a little faster than the limit they seem to smooth out, for some people anyway. I tried it. Then I was told NOT to air down unless going slow! All that sidewall flexing at higher speeds builds up heat in the rubber of the sidewall and can damage tires. Sure enough, after several days I get back on the freeway and the tires have gone way out of balance!

Deaver springs were also recommended to me. Any way to compare them to OME?
 
Did you actually check the wheels / tires to see if they are out of balance ? What type of weights are used for balancing ? Sticky or the clamped hammered on type ?
 
I'll second both airing down and getting good shocks. In my last round of upgrades I switched to Bilstein 7100s so I could choose the valving and it has made a huge difference over the Rancho RS 9000s that I ran for years.
 
What kind of tires do you have? What load rating? This makes a huge difference as well.
 
Did you actually check the wheels / tires to see if they are out of balance ? What type of weights are used for balancing ? Sticky or the clamped hammered on type ?

Yes, went in to the tire shop. The rears both needed rebalance (they handle more load). Clamped on lead weights..
 
I'll second both airing down and getting good shocks. In my last round of upgrades I switched to Bilstein 7100s so I could choose the valving and it has made a huge difference over the Rancho RS 9000s that I ran for years.

On these particular harsh washboards, even aired down to 18psi was still very rough. 35mph speed limit, I was doing about 40, as it seems to smooth out at higher speeds. It's definitely *worse* at 10-25mph.

Are those Bilsteins "reservoir" shocks?
 
Air down to around 12. Those low speeds on dirt/gravel won't overheat the tires and cause any issues. Probably worse for the tires to be at higher pressure getting pounded on the rough roads :twocents:

I run 25psi on cross country interstate trips at 75-80 mph, load range C tires, loaded down, no problems. I drop to 15-20 when I am doing yard work and the associated short trips around town.

Tires are like work boots, unfortunately they can get damaged off road. That being said, my first set of BFG Mud Terrains lasted 10 years/35,000 miles on my red Scrambler. Dry rot, not damage, did them in.
 
Air down to around 12. Those low speeds on dirt/gravel won't overheat the tires and cause any issues. Probably worse for the tires to be at higher pressure getting pounded on the rough roads :twocents:

I run 25psi on cross country interstate trips at 75-80 mph, load range C tires, loaded down, no problems. I drop to 15-20 when I am doing yard work and the associated short trips around town.

Tires are like work boots, unfortunately they can get damaged off road. That being said, my first set of BFG Mud Terrains lasted 10 years/35,000 miles on my red Scrambler. Dry rot, not damage, did them in.

So you're saying up to 45mph is "low enough" speed for 12 psi?
 
So you're saying up to 45mph is "low enough" speed for 12 psi?

I would run 45mph on dirt/gravel roads all day long at 12 psi and not worry about it.

My Scrambler is not too "over weight". If it was a heavier rig, I would not air down as much.

Drop them to 15psi first, see if it is better. If so, go down a hair more. There is eventually a point of diminishing returns. No real exact science to it, you do want a nice big bulge in the tire.

Just take it a little easier going around sharp curves.

When we go to Michigan for "Sand Blast", I air down to 3-5psi to play in the dunes. That is 33x12.50's on stock steel wheels. I will drive the mile/mile and half back to camp on paved roads at that pressure, any further, I would air up.

Most of the time up there, we are airing up and down so much, I will only air up to 15psi, and run that on all the back paved roads we run around on, up to 55mph, no problems.

Every rig is a little different, you just have to experiment.

Tire pressure will help, but if your leaf springs are way too stiff, you need to address that, too :twocents:
 
I would run 45mph on dirt/gravel roads all day long at 12 psi and not worry about it.

My Scrambler is not too "over weight". If it was a heavier rig, I would not air down as much.

Drop them to 15psi first, see if it is better. If so, go down a hair more. There is eventually a point of diminishing returns. No real exact science to it, you do want a nice big bulge in the tire.

Just take it a little easier going around sharp curves.

When we go to Michigan for "Sand Blast", I air down to 3-5psi to play in the dunes. That is 33x12.50's on stock steel wheels. I will drive the mile/mile and half back to camp on paved roads at that pressure, any further, I would air up.

Most of the time up there, we are airing up and down so much, I will only air up to 15psi, and run that on all the back paved roads we run around on, up to 55mph, no problems.

Every rig is a little different, you just have to experiment.

Tire pressure will help, but if your leaf springs are way too stiff, you need to address that, too :twocents:

I've got a hard top, rook rack, heavy box full of spare parts and camping gear in the back! I noticed I could air the front down to 15 and the rear at 20 and get the same "bulge".

And yes, even at 15/20 I really didn't get much bulge! I think bulge is the thing to pay attention too. A good bulge = Sidewall flex. I'll go lower next time, thanks!
 
On these particular harsh washboards, even aired down to 18psi was still very rough. 35mph speed limit, I was doing about 40, as it seems to smooth out at higher speeds. It's definitely *worse* at 10-25mph.

Are those Bilsteins "reservoir" shocks?

You can order with or without reservoirs. Mine have reservoirs because of the collapsed and extended distance required for maximum flex.
 
For another tidbit on pressure. I often run my 40x13.5x17 Cooper STT pro's at 15 PSI...........even commuting 30 miles to work. That's where the tread pattern is nice and they ride good. And very little heat difference from running 25 or 30 psi. On the trails 8 to 10 works well.
 
I wonder if 8" or 10" wheels would work better for airing way down with 33X12.50x15's?
 
I wonder if 8" or 10" wheels would work better for airing way down with 33X12.50x15's?
I've always heard and followed that 8s will hold the bead better when aired down and just work better off-road. I've never used a 10" wide wheel though.
 
I've always heard and followed that 8s will hold the bead better when aired down and just work better off-road. I've never used a 10" wide wheel though.

Good to know. Does anyone know why? More pressure on the bead by pulling it more inward?

Also, the 8" wheels will also weight a little less.
 
Softer Springs: Something I've always wondered...

Won't softer springs allow more body roll? If you swerve at high speeds and the springs flex more easily won't the handling suffer on sharp turns? Could it be argued that stiffer springs are safer on the highway?

I love someone to tell me why this would NOT be true of softer springs!(?)
 
Back
Top