• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Spring over pros and cons

Grey Fox

SOA Member
Lifetime Member
City
Bountiful
State
UT
Just bought a 81 CJ8 that I'm Going to make it a 95% wheeler, maybe 5-10% highway miles. It has what looks like a 3" body lift. I would like to get rid of the body lift returning it to stock. Then do a 4-5" suspension lift. Want to run 33 or 35" tires. At present its a hand full at 40mph so it has steering issues that need to be figured out. My question is for a 4 wheeling jeep isn't a spring over conversion a option to consider?
 
IMHO, defintely worth considering if you want that much height, though even on stock springs a SOA will net closer to 7" (axle thickness + spring thickness + 1/2"). Problem with SOA, to get the most potential from the lift, you need wider axles (for stability), stonger axles (for the larger tires), high steer (to keep it out of the rocks), and transfer case clocking (for center clearance).

The biggest advantage to SOA is the removal of the springs from under the axles which provides an additional 3-4" of ground clearance. However, it's not as easy as a SUA lift so not for the faint at mechanics.

Another thing to consider, if you are going stock springs SOA, you will not gain much additional flex. I find this to be a major advantage in camber situations where you don't get significant body roll. But if you want a lot of flex, go 4.5" lift springs SUA.
 
Where do you come up with this not gaining much flex with stock springs? I've never seen a SUA lift that will outflex stock springs SOA.

You would still want all of those things you listed with a SUA lift.

According to me, SOA is the way to go if you're into leaf springs with 35s or so. You get much bigger and the leafs cant controll so well. But it really depends how you wheel. It worked fine for me for years, but as I pushed it harder I got too much axle wrap and bent springs. Of course the axle wrap could have been solved with a traction bar.
 
Ok, One of the people I've talked to builds tube frame rock crawlers and his beginnings where in building up CJs. He has suggested the SOA, not using the stock springs but a flatter arc spring. Claims more flex, and with a flatter spring a better ride also not such an extreme lift. Wider axles w/lockers are in the plan as well. He did say some type of bracing was needed to prevent the axle wrap. It just seems that the SUA is the preferred method and maybe that's part of the purest way of thinking. Or maybe its like Kohidad said its mechanically harder to do. I just don't want to do something stupid to my new little toy and have someone say you should have ask around before you did that to your jeep.
 
You're not gonna find a spring with less arch than stock. Well I guess you could use stock toyoda front springs, or stock chevy fronts, they both sit negative. But really, stock springs should give you clearance for 35s without looking high. My stock strings with springover gave the same lift as a 4" SUA and worked great with 33s.

Here I'll find a picture.

big_rock-1.jpg


And here's with about 1.5" lift springs and 35s. Notice it is more than 1.5" higher than before, also with full width axles, d44 and d60.

fae5964e-1.jpg
 
Nice rig. I'll be there sum day. So I see you've got a 360 with TBI. Isn't that a fuel injection conversion?. If so that's also on my list. Are you happy with that?
 
That last pic is from a couple years ago, it's changed a few times since then. Yea that's a conversion. Overall I like it. I used the fuel injection and the ignition control from the gm. If I did it again I would stay with the stock ignition control. I don't like that I can't really mess with the ignition without getting another chip burnt. I get a little detonation sometimes when I buy some bad gas. I set the base timing back 2 degrees but it'd really be best to tune the curve. As far as I know, none of the kits use the gm ignition control. You can tune on the fuel a little by messing with the fuel pressure regulator.
 
SOA with yj springs

i'm running 35's with a 4" spring under lift. I'm wanting to run 37's or 38's. I spoke with a friend at a fab shop and he said that yj springs would flex really well. That may be an option, but it does require some relocation of spring brackets on the frame. My question is how much of a lift should i run with cj springs or yj springs in a SOA to clear 37 or 38's. I've installed tj flares on the rear and have tube fenders up front, so that should help with tire rubbing issues. has anyone run this type of setup before?
 
I was running stock CJ springs in my spring over on 37 SSRs. I would get into the fenders but I think part of the problem was the springs were so tired. I just put RE 1.5 lift springs in the rear and they work great.

I don't understand what spring perches you are talking about having to move. In order to use YJ springs they bolt right up in the back and the front you must use a conversion shackle (2" to 2.5") or replace the shackle hangers in the front to rear CJ hangers, then use 2.5" (CJ rear or YJ) shackles.

Truck
 
thanks for the clarification. I probably misunderstood what he was explaining. 1.5" w/ SOA sounds good to me. I think it'll work with my trimmed fenders.
 
The worst thing about SOA is the amount of $$ you will end up spending in the long run "Tuning" it to work properly (controlling axle wrap, springs turning into an "S" shape, etc...) It's worth it but it isn't a Cheap lift.

If you search this site you'll find tons of info.

I run the Rubicon Express HD SOA YJ springs front and rear, have a rear anti-wrap bar and 42" tires, My wrap is under control as well as it can be for leaf springs. It performs well and all but I stil want links. If I could spend the money again I'd probably go linked suspension.
 
Back
Top