• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Turn signal issues

Will_Texas

Legacy Registered User
City
Longview
State
TX
The biggest problem when I got my jeep was electrical issues. I have since fixed a few of the simpler ones, but some still persist and a few more have cropped up. I don't have hardly any experience with electrical problems, so I'm not very good at troubleshooting. I've decided to describe all my problems here at one time.

The most recent is, my blinkers quit working. When I got the jeep, the flasher was busted, and replacing it a first time fixed the blinkers. They recently quit working again, and the flasher isn't the problem this time. I have some interesting symptoms though, the blinker switch doesn't work at all, and when I mash the brakes the front turn signal lights and speedo turn signal indicators come on. So it may have something to do with the brake light switch?

The E-brake light is on all the time. Initially, it didn't work at all, then worked like its supposed to for about a week, and now its on all the time. :rotfl:

Fuel gauge is busted. I know this is a common problem, so any pointers on where to start are appreciated.

Clock doesn't work, and backlight on the tach doesn't work. Maybe a ground?

4wd light doesn't work. I know this is also fairly common.

As expected, my dash wiring is pretty butchered through many PO mods, radio installs, and for whatever reason removing things they didn't deem worthy. I can pretty make out where everything goes, but simplifying the wiring under the dash and cleaning it up is one of my major goals. (Also, if anyone has a link to an 82 wiring diagram that would be amazing, so I can see where all this stuff is supposed to go!)

Thanks in advance for any advice!
 
Hello:
I am the wrong fella to give you advice on electrical issues - only because I do not know anything about it. The guys on this forum will help you out I'm sure.
I did have a problem with my turn signal and my brake lights though at the same time - its a long story and took me forever to located the problem and I only found the problem by accident. I ended up buying a new indicator with the wire harness and replaced the old one with the new one and it fixed my problem (the brake lights and turn signals must be on the same wire harness)???
 
I'm not good with electrical issues either however I also had a small part of what you described as happening - pressing the brake & the right turn signal (outside & in) coming on. Additionally when I turned on my lights the left inside turn signal indicator came on. The culprit was the 4 way flasher switch was partially pushed in. Hope this helps even just a little.
 
maze

A good start is to start with the wiring diagram for sure, here are a few things to check that ive ran across in years of messing with jeeps. check and make sure you have good clean grounds from the frame to the body and the frame to the engine block, next check your light sockets, they are bad about corrision, which will cause all kind of issues, make sure the bulbs are good also. I have run across issues where the contacts where the bulbs make conection to the wiring in the sockets had been pushed out of the sockets and flipped or reversed, just fixed a jeep that the turn signals would work as long as the park/headlights were off but as soon as you turned them on the front signals would quit working, someone had fliped or reversed one of the front sockets in turn signals, i have seen a bad bulb cause issue, jeeps leak everywhere so check your flashers, bulb sockets fuses etc for corroision. there are several other issues that can cause lighting and turn/stop light issues including the turn signal indicator in the steering column that i've ran across. maye someone else can chime in with other things they have found also. Wiring can be such a PIA but just remember take one thing and one wire at a time and it will take some of the sting out, i have printed wiring digrams out and made copies and enlarged them even and taken colored pencils and traced circuits out with the right colored pencil to highlight the circuits im working on to make it easier to trace and then marked them off one at a time when i verified that wire or circuit was good. Good luck with it.:crazy:
 
Back
Top