• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Upgrading tires - issues

Scramblin_Jim

Legacy Registered User
City
Goodyear
State
AZ
I've searched the forums here and read several discussions on the proper tires to use for the specific case being discussed. I didn't see anything that looked like what I want to do so I'm posting this question. Please forgive me if there is a thread out there on this subject and point me to it if you like, otherwise . . .

I picked up another set of chrome wagon style wheels (8"x15) the other day. I was planning on putting some new tires on them for my offroad use and retain my other set for driving around in town. My current setup is stock with Wrangler 30x9.50R15's on them. I notice when out in the mud my last time out, they either didn't have enough tread to bite or they were getting clogged up. In either case, I'd just sit and spin. I don't do much mud driving more desert sand and sharp rocks. I have no rubbing issues now when out flexing my rig with the stock suspension. I suspect it is sagging and needs replaced as do the body mounts. I was thinking of going with an inch taller with a 31x10.5R15 tire like a Maxxis Trepadors.

Q1: Will I have rubbing issues when doing 2.5 rated trails?
Q2: Could I go with a 32x10.5R15 tire or is that pushing it too much?
Q3: Would I be better off putting on a 1" body lift (I already have the parts but not installed for a Daystar standard body bushing kit - no lift)
Q4: Should I address replacing the springs first?

The new tires are for peace of mind when out on the trail but I could keep running the current Wrangler for another 10k miles.

Any advice would be greatly appreciated.
Thanks in advance,
Scramblin_Jim
 
Last edited:
I just put on 31's on to what I assume is a stock suspension (never really checked it out), and I have room to even go to 32's on road, but I would assume that offroad, the 32's would rub. Haven't tried them offroad, but I guess it would depend on how much flexing you do offroad. If just sand, I would thin k you would be just fine...rocks, not positive.

That being said, if you have the body lift, why not put it on, then you will be sure of clearance, now and maybe in the future with 32's...seems like the stock 29's would look a little odd, but looks are subjective.

Got any pics of the stock set-up?

Just trying to help with what I personally know, but I'm sure some more knowledge will come your way from this crew...
 
matnic said:
Got any pics of the stock set-up? ...

My avatar, while small in size here, is the real deal. My bad:
I have 30x9.50R15 on right now, so I'm looking to go to 31".
 
Last edited:
Here's what I did when faced with the "how big a tire can I go with, without rubbing" question. Find yourself a forklift and raise one tire off the ground till the second tire come off the ground. That will be at full flex. Inspect and measure how much clearance you've got and there's your answer.
 
In my experience with no lift of any kind 32s will rub a little offroad but 31s should do it for you with no problems. Small amounts of lift will allow 32s & 33s w/no rubbing.

Truck
 
I have run 31's on multiple CJ's (5, 7, and 8) with no rubbing at full flex. They are the perfect "stock" tire size. My only real problem with 31's is their width. Makes a light vehicle hydroplane pretty easy and snow (up here) can be rather fun on the interstate with wide tires...
 
twmattox said:
I have run 31's on multiple CJ's (5, 7, and 8) with no rubbing at full flex. They are the perfect "stock" tire size. My only real problem with 31's is their width. Makes a light vehicle hydroplane pretty easy and snow (up here) can be rather fun on the interstate with wide tires...

So on a 31" tire, I find 10.50 widths. Would you then consider that a wide tire as it is wider than the 9.50's I have on now? In MHO when going to a 32" tire, a 11.50" or 12.50" width would be W I D E. I'm sure that would be placing a lot of extra stress on the axles, spindles, and other suspension components that would also then need upgraded. I was not planning on doing that for now ($$$). I'm keeping my stock axles and possibly going with a 1" body lift only at this point. That sound good, reasonable? :confused:
 
When I purchased my Scrambler it was stock save for new wheels and 31x10.50x15 ATs that had installed by the previous owner. While I do not recall having had many problems with them rubbing, I always thought that the 31s filled up the front wheel wells just a little too much.

Scrambler-1.jpg


My long term plans included a 1" body lift, so I went ahead and installed the one I purchased from M.O.R.E.. I liked the added clearance it provided. Unfortunately, I do not think I have any pictures of just it installed and my Jeep has evolved a bit more since then.

At any rate, I think that the 1" body lift and 31s make a good combination.
 
For highway use (and given the weight of our rigs) yes, 10.5 is a wide tire. Even with brand new BFG TA/KOs I will hydroplane at a significantly lower speed than a typical mid-sized car. It is always rather embarrassing to be on a very snow covered road going slower than 2 wheel drive cars (because any faster and I can't steer)... All in all, the 10.5 seems to perform very well, you just have to keep in mind your speed at certain times...

On a side note, I absolutely love the wall of water these can inflict on pedestrians when you hit a puddle:D
 
Hmmmm, interesting. I live what most consider a rather wet region of the country and I never noticed the rather conservative 10.50" wide tires having a propensity to hydroplane or give me any problems in snow. I guess I will find out of the new 12.50" wide BFG MTs do. :D
 
Interesting... I do run into a problem when running highway speeds (65+) and there is standing water or snow...

The other thing to remember is that even though 10.5 is very conservatively sized (I have seen monster widths on some mudder trucks around here) it is still nearly 1.5-2" wider than the stock tires...

All of this said, I prefer the 31x10.5 tire size considerably over the 30X9.5...
 
I think you're fine with the 31s, personally I don't think bearings become an issue until the tire weight starts to get excessive more so than the width, unless you are using some weird backspacing. I've run 12.5 x 35s on both my 74 CJ5 and my 82 Scrambler on my stock D30 front and NEVER had a front end issue that I didn't cause via screw up (Hub blew up). Do pack the wheel bearings properly with a good synthetic and keep them snugged up and it won't be an isssue. My scrambler came to me with 33s and a 2.5 in lift and rubbed ever so slightly, not enough to be an issue though
 
matnic said:
Got any pics of the stock set-up?

Here is a picture of the 8 at the airdown spot on last Sunday afternoon/evenings run. I had aired down to 20 PSI and have a nearly full tank of gas - 15 gal tank, 10 gals of water, 5 gal of gas all sitting at the rear tail gate area. Over the rear wheels I had a big ice chest filled with 12 large bottles of water and 3 bags of ice + my tools and spare parts box (weight about 15 lbs). This to give you an idea of how much my poor saggy springs are holding up. :D
 
Jim, I love the simple elegance of your jeep but I think you'd be happier, on road and in the dirt, with some quality 2-3" springs, excellent shocks and 32" ATs (maybe even 33s). One of the things I've noticed over my years of jeeping is that quality springs ARE a huge improvment over the stockers, especially ON road, and with the cost of tires, even 31s, these days, you may be better served to do both a quality suspension and tires together. Personally I don't think there's a downside because eventually you'll want to go a little bigger than the 31s anyway.

Alternatively, If Hi Tech retreads offer a 31 you may want to go that route and save about half the price of new while you evaluate.

just a thought (OK, two thoughts)
 
Thread hijack:

That's a heck of an antenna on your Jeep, Jim. Is that for a CB? How do you like having it mounted there?

WhiteScrambler-1.jpg
 
trust said:
Jim, I love the simple elegance of your jeep but I think you'd be happier, on road and in the dirt, with some quality 2-3" springs, excellent shocks and 32" ATs (maybe even 33s). One of the things I've noticed over my years of jeeping is that quality springs ARE a huge improvment over the stockers, especially ON road, QUOTE]

As fate would have it, I noticed last night as I was blasting off all of the sand from the various cubby holes under the Jeep that my left rear spring is sagging; the Jeep has a definate 1 or 2 inch downward tilt to it now at the left rear only. So maybe the thing to do is put the suspension upgrade and 1" body lift on at the same time (ouch $$$). I was wanting to also upgrade the shocks to air adjustible ones. I was trying to do this as one piece of the elephant at a time approach with just the body lift first, then some moderate (31") height tires, then the 2" suspension lift, and finally bigger (33") tires. I don't think I need to go higher or bigger than that as I am keeping to the lower level trails due to my experience level.
 
Boomer said:
Thread hijack:

That's a heck of an antenna on your Jeep, Jim. Is that for a CB? How do you like having it mounted there?

WhiteScrambler-1.jpg

Yep that is the CB antenna. I was wanting a more central location on the body to give a better ground plane as I had heard that on the tire carrier was not so good a location and could be highly directional expecially when turned 90 degrees to the rest of the Jeeps on the trail. It also provides an easy short cable run to the radio. At this point it seems an OK location. Haven't wacked it on anything, going down the road at freeway speeds doesn't seem to cause too much flexing. Haven't really tried long distance communications tests with it yet.
 
Back
Top