• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

What is this 3 prong plug for in heater duct assembly behind glove box?

sevensandeights

sevensandeights
City
Mckean
State
PA
I should know this but I can't recall what this is for?

xsCk8CY.jpg
 
Thanks! Next question is does the plug for the resistor have to be connected for the blower motor to work? Mine was disconnected and the blower motor didn't work. I connected it but the blower still didn't work. Tested the resister plug with a test light and have power at one of the three prongs with blower switch on. I have yet to test the blower motor by itself.
 
The resistor is what controls blower speed. I think it might work with the fan on high without the resistor connected, but not 100% sure (never tried it... you might have to run a bypass/jumper).

If the resistor is bad, I understand you can use one from a YJ (the CJ version is hard/impossible to come by).
Napa: https://www.napaonline.com/en/p/ECHBR430
 
Last edited:
I am pretty sure (call it 99%) the fan --won't-- work without the plug. The blower motor is grounded to the body/frame on the engine side of the firewall, and the power lead comes through the resistor. It might be possible to bypass the resistor (hooking power directly to the motor side of the connection), but then the speed control switch wouldn't do anything. If you found -that- lead, then the fan would only work when the switch was in the position corresponding to the chosen wire.

B2
 
Thanks! Next question is does the plug for the resistor have to be connected for the blower motor to work? Mine was disconnected and the blower motor didn't work. I connected it but the blower still didn't work. Tested the resister plug with a test light and have power at one of the three prongs with blower switch on. I have yet to test the blower motor by itself.

Make sure to test the ground connection (you can find it coming off the back of the motor on the engine side of the firewall). If you have power to the switch, you can test the three speed positions by connecting your tester between the female connector at the resistor and any good ground. Each of the 3 female connections should only work in the corresponding fan speed switch position (12v to the resistor no matter what, but the connection position determines the voltage drop --and so speed-- to the blower).

If the voltage is good on any of the connections, then the blower should at least work when the switch is on that position. If it doesn't, there are only 3 possibilities: resistor is completely open (no signal at all coming out), bad ground to the blower, or bad blower.

B2
 
I am pretty sure (call it 99%) the fan --won't-- work without the plug.
You are probably correct about needing the resistor to be plugged in. I can't remember if the high speed control wire was direct to the motor supply or if the switch sends power to both the low and medium speed wires at once to make the resistor send full power to the motor (for high speed).

Make sure to test the ground connection (you can find it coming off the back of the motor on the engine side of the firewall).
I believe there is only one wire to the blower motor (this is the power supply that goes to the spade connector on the motor in the engine compartment). Ground is through the case/mount-flange (fiberglass tubs not withstanding). To test the motor you can run a couple of short jumper wires from the battery (one from the battery (+) to the spade connector on the motor and one from the battery (-) to the motor flange/case).
 
Last edited:
Make sure to test the ground connection (you can find it coming off the back of the motor on the engine side of the firewall). If you have power to the switch, you can test the three speed positions by connecting your tester between the female connector at the resistor and any good ground. Each of the 3 female connections should only work in the corresponding fan speed switch position (12v to the resistor no matter what, but the connection position determines the voltage drop --and so speed-- to the blower).

If the voltage is good on any of the connections, then the blower should at least work when the switch is on that position. If it doesn't, there are only 3 possibilities: resistor is completely open (no signal at all coming out), bad ground to the blower, or bad blower.

B2

X2. My money is always on the ground being the problem. I went to the school of JeepHammer and run dedicated grounds everywhere I can including to the blower motor.
 
My fan motor works without this plugged in.....but it only works on high. The low and medium on the switch do not work.
 
Hopefully I have time this weekend to troubleshoot the fan and I'll report back. I have an extra "chevy blower motor" on the shelf but it's such a PITA to install it, especially if the current fan I have is working.
 
As usual - good info on this board! The motor does have power without the resistor plug connected but only in the HIGH position.

My resistor works because when the plug is connected I do have power to the motor in all 3 positions.

However, my fan still doesn't work. It looks corroded and is likely original - it has a "bullet" style connector on a pigtail rather than a spade terminal connect directly to the housing. I will probably upgrade to the Chevy Blazer blower motor now. I already have the dash apart.

My duct cables also need fixed - is the general consensus to go with the MTS products?
 
My duct cables also need fixed - is the general consensus to go with the MTS products?

Omix look sorta original, MTS are built to last.

I'd tear your heater box all apart and smooth the mechanisms out while you're at it. I'm in the middle of it now, took a few hours to disassemble, sand and clean the metal pieces, and paint everything. Probably another couple hours next weekend to reassemble.
 
This Jeep already has billet knobs so I'm not looking for original. I read a post on another forum about cutting off the MTS knobs to allow use of the billet ones and it was pretty straightforward.
 
Not sure what I ended up with probably at least 15 years ago, probably Omix, just replaced 1 of the 3 cables, is functional, but just does not fit up to the dash area correctly, so I would never buy the cheap ones again. Not to worried about the look, functional is what really matters to me.
 
Have a look at these, they're priced high but they look like you'd never have to worry about them. Are they the MTS ones you meant?
 
Back
Top