• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Wits end. Engine has no power or so

I now checked the rear drum brakes and original trac lock differential as I thought that maybe there was something sticking but everything seemed normal. The symptoms seem to be getting worse with the warmer weather. After 30 miles of driving the shuddering starts when driving from a standstill till the clutch is fully engaged. Not when the vehicle sat overnight though. Can't tell for sure but my seat of pants tell me that it drives better when cold and gradually looses power on longer trips. I ordered a DUI HEI ignition maybe that helps.
 
I know I'm late here - but as far as the shuddering, how are your engine and tranny mounts?

Take it out in a flat parking lot and see if it does it in either forward, reverse or both. If it does it in only one direction, it could be your mounts. If it does it in both, it could be your clutch.

Sounds like Jim already hit on this - have you checked yet?
 
The mounts were replaced like five years ago. Everything is thight there. The shuddering is worse in reverse than in first gear. It lessens when driving from a standstill in second. The clutch was replaced a few years ago and has practically no miles on it. I think I didn't understand it right on how to check the clutch though. :shrug: I checked freeplay. Inspected and lubed the linkage.
 
Now installed a D.U.I. HEI ignition and it got interesting. I set advance at 6° BTDC on 600rpm and attached the vacuum advance. The engine almost died!!! I tried a vacuum pump on the advance and the engine startes dying when I get an additional 10° of advance. I checked on the other Jeep we have, which does not care at all if there is much vacuum advance or not and never dies. I finally took it to a shop to check on the exhaust gases and it was running extremely lean. Both in idle and at 2000 rpm. Now I'll be looking for a major vacuum leak which I may have missed before.
 
Got an email from DUI. There are two possible positions for the cap on the distributor. One works, the other doesn't. Now 6° BTDC works well with the vacuum advance attached. I corrected the lean issue with my carb. Set the needles a little higher and turned the vacuum idle screws a little out. Now it runs really well when cold. But after 40 miles the shuddering comes back. I really can't believe that it should be the pilot bushing or clutch. My guess is that if it's worn it dosn't matter when warm or cold.
Another idea of me is that maybe the limited slip starts sticking. But it's just an idea. I can push the Jeep without much effort. Will keep searching.
 
Yesterday I finally removed the clutch assembly. The clutch disk was worn down almost to the rivets even though it is supposed to be in there for appr. 10000 miles. There are receipts to "proof" this. The pressure plate seemed normal. I inspected the flywheel for runout. It was barely within limits having a runout of 0,1 milimeters. It has a glassy surface and you can see on a bout a quarter of the circumference where the higher part was ground down by the disc. It was not discolored though and the surface seems flat. I then inspected the pilot bushing which was OK. The transmission shaft that goes in there was also okay. So right now I'm not sure what to do. Replacing the flywheel is quite costly here and the flywheel is within limits. Is it enough to change the disc and pressure plate and throwout bearing? I don't know. I talked to an experienced Jeep mechanic and he told me they hardly ever changed the flywheel. I don't know.
 
If you're putting in a new dick and pressure plate, have the flywheel resurfaced by a reputable shop. That way you'll have a clean, flat surface to start.
 
I know I am late to this party, and maybe I missed this somewhere, but have you ever dropped your gas tank and checked for rust clogging your pickup filter. I had very similar problems to what you are having...jeep ran fine when cold then ran worse once it warmed up.

But the problem had nothing to do with temperature. It was that the rust particles got stirred up the more I drove, and eventually clogged the pickup filter. As the jeep sat for awhile, they would fall off the filter and settle in the tank, and then it would run well "while cold."

This also fits with your symptoms of running ok at idle, but not when the engine requires more fuel (mine did the same).

I also noticed it would run better with a full tank, which I guess diluted the concentration of the rust.

Anyway, after all you've been through, it is a very quick, easy and cheap job to check the tank and pickup filter, and clean or replace the tank and filter if needed.

good luck and keep us posted!
 
Last edited:
Oh yeah...an easy way to test for what I have suggested without dropping your tank is to just get a gas can and plumb your intake line to that. see if your problems disappear.

Good luck!
-Mike
 
Thanks for the many replies. I finally got it back together. I took it for the usual 50 mile testdrive to work and it ran smooth. I really hope this solved the problem. By the way we now also removed the clutch from my father's CJ 7 which has about 90.000 miles on it and it looked the same like my clutch with 10.000 miles on it. His pressure plate and flywheel were in a better condition than mine. I don't know what abuse they did to this clutch before.
Will test it more to finally believe it that the problem is solved. : )
 
After the clutch removal and replacement of the air filter things got better. However every now and then it would still run like crap. Finally the SOLUTION: PAUSE PAUSE MORE PAUSE TRUMPETS and.....

....................................a defective deceleration valve!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Removed it and it now runs fine. (it only took about two years to find it.) : )
 
Back
Top