• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Rain and motor issue

Wayne

Legacy Registered User
City
Cape Coral
State
FL
Good evening:
If I am driving and it rains I have an issue with the motor.
The motor starts to stall as if It’s out of fuel but it’s not and it back
fires.
Today I was cruising at 65MPH and ran into a storm the motor spluttered, back fired and died I was able to roll through the storm shower, when the rain cleared and the road was dry I was back up to 65MPH.
Any idea what going on??
Cheers,
Wayne.
:banghead::banghead:
 
Spray a lite mist of WD-40 in your distributor cap them reseal the little rubber gasket with silicone.
 
Perfect thank you - what is the WD-40 going to do?
 
Last edited:
It will help remove the moisture. Really carb or parts cleaner would probably work better, just be sure to dry it out before putting it back on. When I was dealing with the same issue on an old CJ7 all I had was WD-40.
 
Developed for US military to displace water out of electric motors.

Water Displacer 40th formula = WD-40
 
Gentleman: Thank you I'm going work on it today. Im not sure what you mean about the rubber gasket but I'm sure I will see it.
Thanks again.
Wayne.
 
Exactly what they said ^^^^^^^^^^.

The WD40 will 'displace the water' so that it isn't causing your spark (rotor / cap) problems. In a lot of distributors, there was a small rubber seal around the bottom lip of the distributor cap itself, where it mates up with the distributor. Some had them and some didn't. I'd also invest a few dollars in a new set of plug wires (simple, cheap and quick to replace), just in case you have a split in the old rubber plug boots and/or wires. And also a new rotor and distributor cap. For less than $30-35 you should be up and running!
 
Exactly what they said ^^^^^^^^^^.

The WD40 will 'displace the water' so that it isn't causing your spark (rotor / cap) problems. In a lot of distributors, there was a small rubber seal around the bottom lip of the distributor cap itself, where it mates up with the distributor. Some had them and some didn't. I'd also invest a few dollars in a new set of plug wires (simple, cheap and quick to replace), just in case you have a split in the old rubber plug boots and/or wires. And also a new rotor and distributor cap. For less than $30-35 you should be up and running!

While you're at it, if you haven't already, you may as well do the Team Rush upgrade. If you're buying replacement distributor parts, that is. And of course, if you're running the 6cyl 4.2.
 
Just run the motor and use a spray bottle and spray mist the spark plug wires and the coil. You'll find the problem pretty quickly-
 
Since you're going to go ahead and be doing the team rush and resealing the distributor, might as well do all the upgrades you can, I've heard the fuel injection works wonders. This is the time you want to reseal and leaky valve covers, oil pans, etc... Of course, doing all this stuff is much easier with the motor removed, its not too difficult. A few bolts and wires and you're on your way. Heck, you might as well get the whole thing rebuilt since you've got it out of the jeep. With the motor out, this is the time to deal with any other mechanical problems you may have. Accessing the engine bay is a lot easier with the front clip removed. This is the time to do rust repairs, with everything easy to access and all. And if you're going to do all that, make sure your wiring is tidy and rewire as necessary. Don't forget to perform any axle upgrades at this step. Since you've already got most of the body parts removed, go ahead and pull the tub for a full repaint. Nothing beats fresh new paint on the underside as well as the outside. Go ahead and have your frame blasted too... Be sure and get something on those inner frame rails so they don't give you trouble in the future...

Oh wait... Did I get carried away?:crazy::eek::wave:
 
Hello again:
I started the motor and misted/sprayed water over the plugs and wires and around the distributor cap and nothing happened, she just kept idling. I checked all the wires going to and from the plugs and they were all on their tight.
I ended up spraying/misting water all over the motor and nothing happened. I took the distributor cap of and cleaned inside and sprayed WD-40, wiped it dry and put the screwed the cap back on. I have attached photos of the distributor.
I had a good look around to see if there were any loose wires or wires that were exposed but everything looked ok.
Any other ideas would be helpful I’m all ears.
Cheers.
 
Last edited:
The ignition module on the fender may be losing it's ground when it's wet too. Do an ohms test to the case from the motor and see what the resistance is. There isn't much else that can cause all of that when it's raining.
 
Check your air intake system, (supplying carburetor or fuel injection). If it is exposed to road spray, water coming through the radiator or hood, it will stop your engine. The intake can only handle a limited amount of water without shutting down the engine. From what you've described/already done, I think you might need to make sure your intake/air filter are protected from excessive moisture.

It sounds like you've checked out the ingition side of the equation well enough to look elsewhere.
 
Rock-N-Roll
Excuse my ignorance but what and where is my intake system?
I have attached a photo with a high lighted area - is this it??
Thanks.
 
Last edited:
I guess I answered my own question - I'm not sure what the hole is on the photo but it's not my air intake system.
 
Stove pipe on the exhaust manifold
You should have a silver flexible pipe on here running
Up to your air cleaner,carb cover
 
Your referring to the photo?
You know I have been looking at the hole forever and I can see that some kind of hose comes of it but I had no idea where it would/is supposed to go?
Great thanks.
Regarding that hole on the side of the exhaust manifold and under the air cleaner carb cover being open and exposed, could that be a reason why my engine stall in the rain?
 
Your referring to the photo?
You know I have been looking at the hole forever and I can see that some kind of hose comes of it but I had no idea where it would/is supposed to go?
Great thanks.
Regarding that hole on the side of the exhaust manifold and under the air cleaner carb cover being open and exposed, could that be a reason why my engine stall in the rain?

Seriously doubt it. But, if water is somehow spraying up through the bottom of the air cleaner assembly where the other end of the hose from the exhaust manifold is supposed to go, maybe, but doubtful:shrug:
 
Back
Top