Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
Thanks John, I found the output term on the Distributor, connected it to the tach while holding it in my hand over the engine and its works. There was a wire connected to that terminal and it go's to the termination block that passes through the fire wall into the interior. However under the...
Help me with wiring up a new tachometer. I bought a new tach that will work on 4,6 or 8 cyl engines. I have a new wiring harness from Painless. I have a HEI distributor on an AMC 360. I thought that I would find a wire under the dash labeled "tach".....Nope. What do I hook this to?
If anyone is thinking about a new frame, I came across this one. Its in Ohio and a pick up only. Seems like a deal You guys out east ought to be able to pony express it around the country...
I hear ya,
It was good to get it out. It was caked in there so bad I stuck a 10ft section of a spring steel fish tape leader in, clamped my cordless drill to the other end and beat holy $#!* out of it. Then got the shop vac hose in to suck it out. I now know why they put those little holes...
Not sure I needed to do this last step but I wasn't sure how strong the frame was at the point where the re-enforcement ended. Didn't want it to break off there after all this work. So I extended the plating forward just on the outside. Again much of the design and inspiration came from...
I hope you guys aren't gettin bored with this.
I bought new shackle mounts and made a new captive nut plate since the original nuts in the frame were toast. This was made from 2 square washers and unistrut nuts, nice and heavy, easy to weld on. This just laid inside the frame over the shackle...
Getting the second radius required clamping heating and tightening. Once formed, tacked it in place to move to the work bench for the finish. Welded up the back and front of the bends then hand grinding put on the finishing look. Welding with the body on made it difficult in some area's...
At this point I took rough measurements and make some cuts so I could get the steel clamped to the frame. Once clamped in place I could refine the fit. You'll notice the body mount was only cut on the sides leaving the top still in tact. I saw this on Chiefwaho's frame repair site, other wise I...
Next I cleaned up the rusted areas and cut out the center cross member.
I bought 2 pieces of steel
3/16" plate X 8" X 60"L With a 2 3/4" bend
3/16" plate X 6" X 10ft L
I knew I had rust and dirt inside the rails so that had to go first. The back bumper was welded on so it had to be torched off. Like I said I knew I had rust and dirt in there but this really surprised me. 20 lbs!
I thought I had an OK frame until I had to drop the gas tank. Was I ever disappointed to find this. The longer I've owned this Jeep the more I'm convinced its lived a hard life. The body mounts have somehow been pulled or rusted out and relocated. The frame rails were full of rust and dirt...
Dan, Thanks. I just got done looking at your website. Love that kind of stuff. I noticed you have taken an evolution of tire "growth". That makes me chuckle in that I can see myself going down that same road. I had a set of borrowed 35's on it at Moab 3 weeks ago. I'm now looking for...
I'm having a full length roll cage built next week. I've got the basic design drawn up. Any doe's and don't? I've seen some where the bar by the top of the windshield has some sort of tabs? Not sure what those are for, Isn't the windshield self supporting? Any suggestions on if I had to do it...
Great shots and nice post. Tell me how you are attatching your pictures and they show up. I mean when I have attatched pictures they show up as an attatchment and have to be clicked on to see them.
I'm in the middle of doing this exact repair. My rust spots are in the same location and probably as bad if not worse than yours. I'm using 3/16 plate steel to box in the area. I'm taking pictures of the process and was planning on posting them in 2 or 3 days when I get a little further on...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.