• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

100 day summer rebuild

I'm going to fix the yoke on friday...

if i tala differential apart and removing the yoke require i adjust the shimming?

Huh? Sounds like you are acclimating to college life. LOL
 
well i don't have the scrambler with me at school but i can tell you a little bit about it!

.
.

No rush, but when you get a chance, can you snap some good pics of it?

Thanks!

.
.
 
haha.... what i meant to say was..... if i change the yoke will i need to change any of the shims?

theres are all the pics i have of the tan one right now...

IMG_2155_zps6cd20f50.jpg
[/URL][/IMG]




 
Depending on the condition, the doors and top fetch a good amount as well. Good luck parting it out. Should be able to make a nice little profit.
 
And someone here was looking for the Scrambler emblems on the rear sides.
 
I know I'm late to this party, but I still see the cross-member that you welded up underneath your 8. I concur that I don't think it has the integrity required, nor does it account for the torque-arm that's incorporated into the OEM skid/cross-member. I think you're lucky it hasn't fallen out yet.

It's hard to be certain, but I believe the cross-member your Scrambler came with is, in fact, an OEM late-model cross-member. I'm not sure why it was installed the way it was installed (with the angle-iron), but that's obviously not the original location. You'll also note more nutserts welded inside your frame than is necessary; that was originally done to accommodate the cross-member in multiple locations for different transmission/t-case combinations. Again, it's hard to tell, but I'm thinking that maybe the PO decided to try to install the drivetrain forward a couple inches? Or maybe to accommodate the T-18/Dana 20 combination, they relocated the late-model cross-member rather than acquiring an early-model cross-member?

As for OEM, I agree with what has been posted before, and will confirm that the 304/360/401 will work just fine with either OEM cross-member; the back of the 258 is located in EXACTLY THE SAME PLANE as the back of the V8 family when put in a CJ, with OEM (or OEM replacement) engine mounts. Running the late-model cross-member with a T-18 requires a very minor bend in the leading edge of the cross-member, but it will otherwise bolt-up perfectly. Running the early-model cross-member (that came factory with the T-18/Dana 20 combination) should require no modifications whatsoever.

Otherwise it's a great project! I love seeing more people running AMC V8 power! (But seriously, fix that cross-member issue before your transmission falls out. T-18s and Dana 20s are heavy.)
 
Last edited:
.
.

Glad to see you got it repaired and at school with you - just refrain from the urban wheeling as much as possible...nothing good will come from it!

Thanks for the additional pics of your parts Scrambler too. Looks awfully similar to one of my old ones that was sold back in '98 or '99 when it was in much better condition.

.
.
 
some projects here and there, beefed up the cross member (know that should make a lot of you happier), had the hole front end professionally rebuild after i bent the tie rod and drag links off roaring. got a 54in light bar, harbor faith winch, and i made that fast back hard top!!!

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]
 
forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]

forum
[/URL][/IMG]
 
Dude! Way Cool!

Looks like a 67 Jeepster convertible top. I like it!
 
Back
Top