• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

4.0 fuel pressure regulator & flywheel

PAPPYWAHO

Enjoying Retirement
Lifetime Member
SOA Member
City
Thayer
State
KS
I have installed a 1995 Grand Cherokee 4.0 eng in my 81 Scrambler. This eng does not have a fuel pressure regulator on the fuel rail and does not have a return line to tank. I want to mount an inline fuel pump, regulator, and filter (or filer/regulator combo) at the tank area. I believe I will need a constant 39.5 pressure at the fuel rail. Looking for someone's experience or suggestions on what I should use.
Any help would be appreciated.
 
Last edited:
I’m no expert here, by any stretch, but I have access to a 93 ZJ and 96ZJ FSM.

The 93 is obviously OBD1 and has the pressure regulator on the fuel rail. The 93 fsm says pressure should be 31 at idle. The 96 is OBD2 and has the regulator in the tank. The 96 FSM says pressure should be 49 at idle.

I think the 95 is one of those orphan years where there is no return line, but you are still OBD1. So I think your simplest option would be to get fuel rail from another OBD1 motor and run a return. If you’re actual OBD2, then the filter/regulator from a WJ would work for 49PSI.

I miss CJOffroad.com
 
Thanks for your reply. To keep things simple I have changed out the fuel rail and used one from an early 1990s Cherokee that had the rail regulator and the return line set up. I installed an E2000 in line pump with a pre-filter. I now have fuel at the rail. Now on to my next problem, grtting it to fire.
 
Cool, didn't know y'all were working on a 4.0 swap. Sounds like a good way to go on the fuel setup, good luck firing her up!!
 
Fires on # 3 & #4 only

Now that I have fuel at the rail, I can crank and only get spark out of #3 & #4 post at the distributor. Changed out to new cap and rotor and even changed out distributor and got the same results. Coil and PCM are good as I have pluged them into an 94 Cherokee and everything worked great. This is my first time working with an engine that has PCM, PDM, Fuel Injection and with sensors everywhere so not sure how everthing works. The 1995 Grand Cherokee donor had an automatic and I have installed a t-176 tranny with a 1995 flywheel and did my own CPS install at the T-176 bell housing. Also grafted in the 1995 wire harness. I suspect this CPS may be my problem. Can this CPS be located off enough to only send a signal to #3 and #4??? The sensor is located 2.425 off the the top belllhousing bolt hole and I have a .025 gap at cps to flywheel. Before I break out some of my stash (money hid from the wife) and buy the Hesco CPS kit I thought I would post up to see if any body had some trouble shooting Ideas to throw at me.
 
first let me say that I dont know personally how everything works together, but here is what I was told by a guy last week, who works for MOPAR, on the EFI kit (which I have). He says his Wrangler was used to prototype the MOPAR kit and in looking at my installation he made the comment that he thought th egap on my CPS (mounted on the front of the engine) was to great but if it works dont monkey with it they either work or they dont. So with that as a background I would guess that your CPS set up is at least part of the problem. You could get the HESCO front mount and CPS or look into a bellhousing for a 4.0L with a manual trans and see if that would work with your tranny. I would guess that only 3 and 4 spark because they are in the middle of the engine and can tolerate the most out of spec feed back from the sensors.

I assume you checked the coil

Mine also has the no regulator no return line fuel rail and came with a regulator that mounts at the tank with the pump and filter. All of those parts (or an adjustable regulator) an be had from HESCO as well
 
I wouldn't be surprised if it was the CPS, but have nothing to back that up other than it seems to be a very common culprit. Nothing else comes to mind since you eliminated the coil, PCM, cap, rotor, dizzy.
 
Are you getting no signal at all from the other plug positions, or not at the right time???

There can be an issue with the Dist. not being at the right place and needing the ear to be cut off and turned. There is a procedure for doing this from Mopar.

Sounds like it might be a CPS or CPS gap issue. that gap is supposed to be set really small. The size of a match book cover IIRC. When they are new there is a sacrificial piece of paler that can be used to set proper distance.

Lately I go to the Stroker site to get info on properly setting up the MPFI systems. It used to be CJoffroad.com was a good place but they appear to be shut down.

Try this place, lots of hot rod heads over there.

http://www.jeepstrokers.com/forum/

This is an offshoot of the original Yahoo e-mail forum on Jeep Strokers.


Carl
 
Thanks guys for your input. I have another clue that might help to determine the problem. I have this circuit testing light that I can plug in between the coil and the distributor and between the plugs and the distributor. When I plug in between the coil and the distributor and steadily crank the engine the tester appears to show a continuous steady rhythm of spark light. When I plug in between each plug and distributor I only get a spark light at #3 & #4. I have checked plugs and plug wires and they are good. I think maybe the camshaft position sensor is not receiving a good solid signal from the crankshaft position sensor. Will try to adjust location of CPS today.

Went to the jeepstrokers forum yesterday. Good forum.
 
If you are looking to do a stroker sometime. check out the thread where I posted a link to YJ&Cory's write up on doing a proper one. There are full part numbers and everything. His engines have done pretty well for him.



Carl
 
I think I have found my problem. The supplier of my 4.0 flywheel sent the wrong flywheel. Packing list and invoice had correct part #. Notches are not at correct spacing on the one I have installed and is probably confusing my complete system. :shrug: I have sent the supplier a picture of the one they sent me for comparison. Hope they will ship me the right one.
I now have to drop the tranfer case, tranny and remove bellhousing and clutch assembly. Good thing I am retired and have time to tinker.
Thanks to you guys who took time to ponder my problem.
 
Last edited:
Wow, not sure I'd have ever thought to check that... :crazy: Good find!!

What a pain to deal with though! :banghead:
 
What a PIA for a screwed up part that should have been right.
 
Battle is on

Well now I am ticked. The supplier of my flywheel who sent the wrong one will not stand behind their shipping mistake. Reason: The 90 day warranty is up. Never mind that it is still new and that it took them 2 tries and over 30 days to get it shipped to the right address. It has been in my possession for about 2 months. The battle is now on. If they do not replace the flywheel I guess my only satisfaction is to let everyone out in the internet world know who they are so potential customers will be aware of how this company handles business.
In the meantime I have borrowed a correct flywheel off a used 4.0 that had a standard tranny and will have it installed tonight. Fingers crossed, it will be fired up shortly.
 
I have now installed the correct flywheel and guess what? :woot: The dang thing started up. Jason just gave me a high five. :cheers: Does not sound to pretty with no muffler, but she does run. Now to thin out some wires and get it loomed up and go for a ride.
 
Sounds like they sent you a Renix Flywheel.

That is a hard thing to diagnose if you do not know what to look for.

Great that you figured that one out. That would have been a really hard one to figure out over the internet. I think that you will really enjoy the new system.


Carl
 
Back
Top