• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

610 lbs-ft of Torque!!??

canzo

equal opportunity annoyer
City
Alexandria
State
VA
I comparing truck engines at Dodge.com and it was saying that the 5.9L I-6 engine puts out 610 lbs-ft of torque at 1600 rpm!!!:eek:

Is this right? :confused:

That would be an awesome engine for a Jeep! :cool:
 
thats the diesel engine. And it would be way too much torque for a Jeep to harness
 
Not to mention too much weight to make it pratical. My front axle weighs in almost to 5,000 lbs empty.

Yes, the numbers are right. Nothing like burning rubber with an 11,000 pound fifth wheel attached. :D

Empty, I can break the back end loose in 3rd sometimes. If the pavement is wet, can do it in fourth easily.
 
Not to mention you would either have to lengthen the front clip or set the motor back into the firewall and then you would have to run 1 ton running gear and at least 3/4 ton springs in the front just to handle the added weight on the nose...........But man it would be a pulling SOB:D
 
The 4BT which is a cut down version of the 6bt in the Dodge would be a better choice.

Even that monster is a bit big for a CJ, but several have made it work. Frito Lay vans are the current preffered method of obtaining one for the transplant.

But there is a guy in ND that is working on getting a 3bt to run in a YJ. It is an industrial engine. But he has it driving and has begun to hot rod it. A really nice install.

Carl

http://www.dieseltruckresource.com/dev/showthread.php?t=112807
 
Here's a 4BT that was in a extremly nice CJ-8, from Jeepfest the past 2 years. It's got a 4wd hardware glass body and a full hardtop, The drive line is fairly lame with 33's and only d44's but it's got the 4BT, a NV4500, and a D300. I want one bad I figure if the 6 can be turned up to 1200 HP the 4 ought to bring a easy 250-300HP and 500ftlbs.
diesel2-1.jpg

diesel1-1.jpg
 
bones said:
way too much torque for a Jeep to harness

There's no such thing!! :D

I was thinking it was a diesel, but there was no mention of the diesel fuel in the chart I was looking at. And just think, you could make your own biodiesel for about 60-80 cents a gallon and wheel all day and night long. :cool:
 
The first 6BTs had so much torque they twisted and cracked the full size 3/4 ton Dodge frames they were mounted in. After that first year I think all the trucks with the Cummins had a beefed up frame and suspension. (the sucker weighs close to 1,000 lbs!)
 
Fudd said:
The first 6BTs had so much torque they twisted and cracked the full size 3/4 ton Dodge frames they were mounted in. After that first year I think all the trucks with the Cummins had a beefed up frame and suspension. (the sucker weighs close to 1,000 lbs!)

I believe that the 6BT was also detuned a bit. Which may help to explain why significant power gains can be had from the 6BT so easily and inexpensively.
 
Same with 4BT's they are pretty conservitive at the factory. By just bumping up the fuel there is a good bit to be had.

Add a better exhaust and a pro Diesel guy turining up the wick you can make the 4 pretty potent.

Carl
 
The 98.5-2001 24 valves are detuned 275 hp motors. They use smaller injectors to drop 60 hp for an automatic and 40 hp for a manual. The 6BTs from 94-98 were also detuned but I'm not sure how much. But the real reasone you can get more power from a turbo diesel easily is because all you have to do is add more fuel and air as with any engine, but they've allready got the turbo to make it easier, and there's no worry about spark knock.
 
I had an entire fleet of Freightliner meduim duty (33,000 GVWR) trucks with 24' boxes and 6BT engines. My point being (to back up what is already said) they are much more capable (can put out a LOT more power and torque) than the way they are setup from Dodge.

Good engine...
 
Back
Top